Procedure 10.16: SWAP DISK PACKS IN 300-MB SMD MOVING HEAD DISK DRIVE
OVERVIEW
This procedure describes the swapping of disk packs in the 300-MB storage module device (SMD) moving head
disk (MHD) drive. The covers of the disk drive should never be left open longer than the time it takes to change
disks.
PROCEDURE
1.
On moving head disk (MHD=x) to be swapped, raise the cover on the start switch and push the switch.
Response:
READY
lamp begins to flash.
2.
Wait for disk to stop spinning (
READY
lamp stops flashing).
3.
Remove bottom of an empty disk pack cover assembly.
4.
Open
outer
cover of disk drive.
5.
Open
inner
cover of disk drive.
6.
Place disk pack cover over disks
immediately
.
7.
Turn handle
counterclockwise
until it is tight.
8.
Lift the disk pack clear of the drive
carefully
.
9.
Put bottom cover on the disks.
10.
Put disk pack on shelf and label appropriately.
11.
Load the pack to be mounted by opening the outer pack access cover and the inner pack access cover and
placing the pack on the spindle. Be sure to disengage the bottom dust cover from the disk pack before setting
the pack on the spindle.
12.
Turn the pack clockwise until it is secured to the spindle lockshaft.
13.
Lift the top dust cover clear of the drive and store it with the bottom dust cover.
14.
Close the inner pack access cover immediately to prevent entry of dust and contamination of the disk
surfaces. Close the outer pack access cover.
15.
Turn off the 46-volt breaker on the drive power supply. All the other breakers should be on, including the main
AC.
16.
Press the
start
switch in order for the blowers to start purging the pack.
Response:
FAULT
light on.
READY
lamp flashes.
17.
Wait for the pack to be purged the desired amount of time.
235-105-210
October 1999
Copyright © 1999
Page 1
Summary of Contents for 5ESS-2000
