Lucoro Broadcast FMTX100 User Manual Download

Page: 13 / 15

RF:
Frequency range

87.5 to 108.00MHz

Frequency stability

Better than ±200Hz

Output power

30 - 125W

Harmonic & spurious output

-75dBc typical

AM Noise

<0.5% @ ±40kHz deviation

THD

<0.15%@ ±75KHz deviation

RF output connector

‘N’ type (F)

Monitoring:
RF

BNC (F) -40dB 50 ohms

MPX

BNC (F) 1V P-P 10K ohms

Audio Interface:
Audio Input Level

+8dBu for ±75KHz deviation

Audio Input Impedance

600 Ohms

Audio input connectors

XLR (F)

RDS:
Groups

0A & 2A (others on request)

Power Supply:
Input AC

100V to 250V (50/60 Hz)

Consumption (maximum RF output)

250W (230V 50Hz)

Mechanical:
Size (mm)

2U 88 (H) x 482 (W) x 290 (D)

Weight

5kg

Temperature

0ºC to +42ºC

Humidity

95% (relative non-condensing)

We reserve the right to alter specifications without notice. E&OE.

Technical Specifications

Summary of Contents for FMTX100
















Search results

Summary of Contents for FMTX100

Reviews:

Related manuals for FMTX100

Brands by name

Popular brands

Lucoro Broadcast FMTX100, User Manual

Search results

Summary of Contents for FMTX100

Reviews:

Related manuals for FMTX100

Brands by name

Popular brands