Lucoro Broadcast FMTX100RBRX User Manual Download | Manualshive

Page: 10 / 14

background image

Ensure air vents and internal air tunnels are kept free from dust during
operation.

The cooling fans should be replaced after 40,000 hours of cumulative
operation. This life rating is for guidance only and is subject to ideal
environmental operating conditions. Replace any fan that fails or
becomes slow or noisy, immediately. Replacement fan assemblies with
wiring loom and mating connector are available from the
manufacturer. It is recommended that replacement work must be
carried out by the manufacturer or an approved agent.

«
...
8
9
10
11
12
...
»

Summary of Contents for FMTX100RBRX















Reviews:

No comments

Related manuals for FMTX100RBRX

Brand: Icom Pages: 5

Brand: halstrup-walcher Pages: 34

Brand: Uhlenbrock Elektronik Pages: 12

Pursuit PRO-OE3B3

Brand: Audiovox Pages: 4

Cerabar T PMP 135

Brand: E+H Pages: 12

PluraSens E2638-NH3-P

Brand: Evikon Pages: 21

BDG D 60-H020-NUS01-1318-0000-S4L4 Series

Brand: Balluff Pages: 94

Brand: Vector Pages: 3

Brand: Aluprof Pages: 4

Brand: C4Line Pages: 2

Brand: M-system Pages: 7

Brand: Icom Pages: 3

Brand: silentgliss Pages: 29

Brand: Omni-WiFi Pages: 11

Brand: M&C Pages: 17

Brand: AquaScape Pages: 2

Brand: Teslink Pages: 5

Brand: Icom Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands