User’s Guide ...
13
12
... LUKAS BLACKBOX
6. Firmware update and function comparison
Power cable connection method
1. Download the attached compressed file from the homepage.
(Download the firmware by confirming the model you use.)
J-21 / JE21 : LK-3700G, LK-2700G
C-21 / CE21 : LK-3700, LK-2700
Firmware of E version is a piece of firmware of the function to store a file separately
when an event happens.
2. Copy the important content of a SD card into another storage medium, and then
format
it
by all means.
3. Decompress it and copy the 3 files such as LukasMainImage.bin, LucyEboot.bin and
memInfo.bin into a SD card.
4.
Start the car. (This is to prevent power from being intercepted during an update.)
5. Put it in a black box and then turn ON power. If a word SD_FAIL appears in the black
box, insert the SD card.
6. The buzzer in the black box goes off 4 times to display the update rate in numbers.
7. After an update, it is automatically rebooted.
8. The update has finished.
Firmware during product shipment: J-21(3700G),C-21(3700),JE-21(2700G),CE-21(2700)
- In order to confirm the detailed content of firmware update methods and cautions, visit
www.lukas.or.kr
.
- This instruction manual was produced as of now, and the firmware is subject to changes for
performance improvement without prior notice. [issue date: July 2011]
LED ON/OFF function Used
Not used
Time band
Correction of a GMT time band and addition of a summer time
setting
by GPS (used overseas)
Separate setting of
G sensor sensitivity Separate operation of sensitivity setting in travel and parking
during parking
Automatic
- Checking of automatic conversion of travel modes in terminal
conversion of
environment setting
travel modes
- A function of detecting the vehicle travel in a parking mode and
converting it into a travel mode
Automatic
- Checking of automatic conversion of parking modes in terminal
conversion of
environment setting
parking modes
- A function of detecting the vehicle travel in a travel mode and converting
it into a parking mode
Addition of Video The video out that supported NTSC only previously can be used as PAL
Out PAL
through environment setting. (used overseas)
Addition of a high - Checking of use of a high temperature safety mode in terminal
temperature environment
setting
safety mode
- Safety mode voltage condition: If the vehicle room temperature reaches
a high temperature environment(65 ), it gets into a safety mode in
1 hour, and at this time, the entry is notified by 1 long beep sound and
3 short beep sounds, and a word SAFE flashes on the SEG window.
When getting into a safety mode, recording stops. This is to protect the
product from a high temperature environment.
- Safe mode cancellation condition: When 1 minute passes below 65
of
vehicle room temperature, the safety mode is cancelled, and at this time,
the beep sound notifies it in the same way as the recording start sound to
start a recording mode again.
"[Warning: Over Temperature!!!]" is displayed at the lower middle of an
image file below 65
of room temperature.
Comparison of functions pursuant to firmware versions
Firmware version and J-21 (LK-3700G,LK-2700G)
C-21 (LK-3700,LK-2700)
application model JE-21 (LK-3700G,LK-2700G)
CE-21 (LK-3700,LK-2700)
MODE
Normal / event / parking
event / parking
Storage time
5 min
3 min (separate storage of events
for 30 sec)
Storage type
Storage of a normal recording
Creation and storage of a
pursuant to a
file and an event recording
separate folder for an event
recording mode
file in a folder
recording file
Recording unit
Normal recording: 5 min
Normal recording: 3 min
Number of stored files
Storage of 200 files per folder
Storage of 150 files per folder
Memory partition
100% use at a normal mode
Normal : event=75%:25%
