background image

Part I: General Safety Rules 

 

 

Safety for Children and Pets 

 

 

 

WARNING 

Tragic accidents can occur if the operator is not alert to the presence of children and pets. 

Children  are  often  attracted  to  the  machine  and  the  chipping  activity.  Never  assume  that 

children will remain where you last saw them. Always follow these precautions: 

A.

 

Keep children and pets at least 50 feet from the working area and ensure they are under 

the watchful care of a responsible adult. 

B.

 

Be alert and turn the machine off if children or pets enter the work area. 

C.

 

Never allow children to operate the Wood Chipper. 

 

Safety with Gasoline - Powered Machines 

 

 

 

WARNING 

Gasoline  is  a  highly flammable  liquid.  Gasoline  also gives  off flammable  vapor that  can  be 

easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always 

follow these precautions: 

A.

 

Never  run  the  engine  in  an  enclosed area  or without  proper ventilation  as  the exhaust 

from the engine contains carbon monoxide, which is an odorless, tasteless, and a deadly 

poisonous gas. 

B.

 

Store all fuel and oil in containers specifically designed and approved for this purpose 

and keep away from heat and open flame, and out of the reach of children. 

C.

 

Replace  rubber  fuel  lines  and  grommets  when  worn  or  damaged  and  after  5  years  of 

use. 

D.

 

Fill  the  gasoline  tank  outdoors  with  the  engine  off  and  allow  the  engine  to  cool 

completely. Don't handle gasoline if you or anyone nearby is smoking, or if you're near 

anything  that  could  cause  it  to  ignite  or  explode.  Reinstall  the  fuel  tank  cap  and  fuel 

container cap securely. 

E.

 

If  you  spill  gasoline,  do  not  attempt  to  start  the  engine.  Move  the  machine  away  from 

the area of the spill and avoid creating any source of ignition until the gas vapors have 

dissipated. Wipe up any spilled fuel to prevent a fire hazard and properly dispose of the 

waste. 

F.

 

Allow  the  engine  to  cool  completely  before  storing  in  any  enclosure.  Never  store  a 

machine that has gas in the tank, or a fuel container, near an open flame or spark such 

as a water heater, space heater, clothes dryer or furnace. 

G.

 

Never  make  adjustments  or  repairs  with  the  engine  running.  Shut  down  the  engine, 

disconnect  the  spark  plug  wire,  keeping  it  away  from  the  spark  plug  to  prevent 

accidental starting, wait 5 minutes before making adjustments or repairs. 

H.

 

Never tamper with the engine

s governor setting. The governor controls the maximum 

safe  operation  speed  and  protects  the  engine.  Over-speeding  the  engine  is  dangerous 

and  will  cause  damage  to  the  engine  and  to  the  other  moving  parts  of  the  machine.  If 

Summary of Contents for RAMBO-HC10


















Reviews: