background image

IMPAC pyrometer IGA 15 plus

 

 

 

 

2.4 

Scope of delivery 

Instrument (incl. battery), carrying case, inspection sheet, user manual. 
 
 

3

 

Safety 

 
This section offers an overview about important safety aspects. Additionally in the several sections 
there are concrete safety aspects to avert danger. These aspects are indicated with symbols. 
Labels and markings at the instrument have to be observed and kept in a permanent readable 
condition. 
 
 

3.1 

General 

Each person working with the pyrometer must have read and understood the user manual before 
operation. Also this has to be done if the person has already used similar instruments or was 
already trained by the manufacturer.  
The pyrometer has only to be used for the purpose described in the manual. It is recommended to 
use only accessories offered by the manufacturer.  
 
 

3.2 

Laser targeting light 

For easy alignment to the measuring object the pyrometers can be equipped with a laser targeting 
light. This is a visible red light with a wavelength between 630 and 680 nm and a maximum power 
of < 1 mW. The laser is classified as product of laser class II.  
 

 

 

Warning:

  To reduce the risk of injury to the eyes, do not look 

directly into the targeting laser and do not point the 
targeting laser into anyone's eyes. The instrument is 
equipped with a class II laser that emits radiation. 

 

 

Safety regulations: 

  Never look directly into the laser beam. The beam and spot can be watched safely from side.  

  Make sure that the beam will not be reflected into eyes of people by mirrors or shiny surfaces. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for IGA 15 plus















Reviews: