background image

4

Model No.: RCK55

Reverse Module Installation (Continued)

2.5: For Ceiling Fan Model CF2400 ONLY.

14. Locate the Capacitor Gray Wire which is 

connected to the Gray Wire coming from the 

Center of the Motor (yellow wire on older 

models) (Figure 5). 

15. Remove the Wire Connector and separate these 

Wires. 

16. Cap the Gray Wire coming from the Motor using 

a Wire Connector (supplied) (Figure 5).

CF2400 - INSTALL WIRE 

CONNECTOR ON GRAY 

WIRE

(

CF1 & CF2800 - YELLOW  

WIRE

)

CF2400 GRAY WIRE 

(

YELLOW WIRE ON 

NEWER MODELS

)

CAPACITOR 

GRAY WIRE

CAPACITOR

  Figure 5

SWITCH 

HOUSING

REMOVE 

CAPACITOR/ 

WIRING HARNESS/ 

SWITCH(ES)

FROM SWITCH 

HOUSING

  Figure 6

2.6: All Ceiling Fan Models.

17. Separate the Capacitor (held in place with 

two-sided tape) from the Switch Housing 

(Figure 6).

18. Remove the Wiring Harness and Switch(es) 

from the Switch Housing.

NOTE: Keep the wiring harness if you think you may 

like to return to manual control in the future.

SWITCH 

HOUSING

RECTANGULAR PLUG

PULL CHAIN 

SWITCH PLUGS

  Figure 7

2.7: All Ceiling Fan Models.

If Not Already Completed:

19. Close the Hole(s) for the Speed Control Switch, 

the Uplight Switch, and the Reverse Switch 

by installing Pull Chain Plug(s) (supplied) 

or Rectangular Plug (supplied) in the Hole(s) 

(Figure 7). 

 

Choose the color that best matches your Ceiling 

Fan.

Summary of Contents for RCK55













Reviews: