background image

 

by momentarily pressing onto it.   To adjust the numbers, rotate the 
Super Controller in either direction.  To switch between numbers, press 
onto Super Controller momentarily.  After Date is set, adjust the time.  
Time is in 24hr format, so 13:00 is 1pm; 17:30 is 5:30pm and so on.  As 
with the date, changing hours and minutes is done by rotating the Super 
Controller and moving between hours and minutes is done by pressing 
onto it.  Once the time is adjusted you may choose to change the date 
format to MM/DD/YYYY or YYYY/MM/DD according to your preference.  
Once you are finished setting date and time, you can exit the menu by 
pressing Super Controller (9) for approximately 2 seconds. Once set, the 
time will be displayed on the bottom of the OLED image display. 
IMPORTANT: in order to preserve the set date/time do not remove the 
dead batteries from the unit until you are ready to replace them with 
the new set, then replace the old batteries with new set as quickly as 
possible and the date/time will be preserved. 

 

USING INFRARED ILLUMINATOR: 

Your digital viewer is equipped with a built-in powerful Infrared 
illuminator light (7).  This light operates in a spectrum, which is normally 
invisible to a human eye, however with the help of the CCD sensor, 
located inside the unit, you will see a beam of light when looking though 
the ocular lens.  Since the CCD does not actively amplify the available 
light, you will need to utilize the IR illuminator often in the nighttime 
conditions.  

 

To turn the Infrared illuminator ON, press the Infrared illuminator 
button (4) momentarily – the IR icon will appear on the bottom of the 
display and red LED light indicator (10) located next to the eyepiece will 
light on, indicating the IR illuminator is operating.  The illuminator 
intensity can be further increased by pressing the IR button (4) second 
and third time (momentarily). The IR icon in the image display will 
change colors from pink to orange to red, indicating the three different 
power levels.  After the red level (3

rd

 and most powerful) the next 

momentary press on the IR button will turn the IR off completely. The 
red LED light indicator (10) will disappear when the IR illuminator is 
properly turned off. 

 

When using the infrared illuminator it is important to remember that 
like a flashlight, it is brightest when used in short distances.  As the 
distance increases, the intensity of the infrared light fades away. 

 

Summary of Contents for LN-G3-M

















Reviews: