Lutron Electronics Softswitch128 Installation Manual Download

Page: 4 / 16

Step by Step Installation Instructions for Softswitch128

System

Step 1
Panel Dimensions

24” Mini Panel Dimensions

Bottom View

Top View

Right Side

Left Side

The dimensions are shown in inches and (mm).

When surface mounting, the keyholes
accept a maximum of 1/4 in. (6 mm)
mounting bolt. This size is
recommended. When flush mounting,
mount the panel between flush and 1/8
in. (3 mm) below finished wall surface.

Suggested Mounting Height:

Mount Mini panels 45 in. (1143 mm),
above the floor (measured to bottom
of panel) for optimal Controller viewing
height.

Front View

14.38 (365)

15.875

(403)

8.00

(203)

2.2 (56)

4.2
(107)

0.5 (4)

1.34
(34)

21.50
(546)

24.50
(622)

24.00
(610)

2.21
(56)

15.13 (384)

10.75
(273)

4.09
(104)

Cover

Summary of Contents for Softswitch128

















Search results

Summary of Contents for Softswitch128

Reviews:

Related manuals for Softswitch128

Brands by name

Popular brands

Lutron Electronics Softswitch128, Installation Manual

Search results

Summary of Contents for Softswitch128

Reviews:

Related manuals for Softswitch128

Brands by name

Popular brands