14
2. Reciprocating protective hood
3. Clamping fixture
4. Locking screw for mitre angle
5. Locking lever for mitre angle
6. Saw bench
7. Bench extender
8. Workpiece stop
9. Locking screw for incline adjustment
10. Laser
11. Handle
12. Shaving rejection chute
13. On/Off switch for laser
14. Battery compartment
15. Setscrew for cutting depth limiter
16. Support handle
17. Locking screw for pulling device
18. Safety bolt
19. Release button
20. On-Off switch
Scope of supply
• Chop and mitre saw
• Support handle
• Clamping fixture
• Collecting sack
• Bag with small parts
• Instructions for use
Assembly
– Press handle (11) gently downwards and
keep it pressed.
– Pull out the safety bolts (18).
– Slowly guide the tool arm upwards.
– Push the clamping fixture (3) into one of
the holes provided and screw down with
bolts (21).
– Push the support handle (16) into the
holes provided and screw down with
bolts (22).
Mount the device onto the workbench
– Insert suitable screws through the drilled
mounting holes (31).
– Firmly screw the product to the bench
surface.
Attaching the collecting sack
– Push clamp (24) together.
– Attach the collecting sack (25) to the
swarf remover or connect a swarf extrac-
tor.
Operation
Check before switching on!
Check the safe condition of the product:
– Check whether there are any visible
defects.
– Check whether all parts of the product
are firmly attached.
– Check that the product is stable.
– Check that the safety devices are in fault-
less condition.
– Check whether the incline setting locking
screw is firmly tightened.
–
Sawing without using the pulling
device:
Check whether the locking screw
of the pulling device is firmly tightened.
–
Sawing using the pulling device:
Check
whether the locking screw of the pulling
device is released.
Setting the bench width
– Pull the bench width extender (7) out to
the required length and lock with the
locking screw (23).
Setting the mitre angle
The mitre angle can be set steplessly
between -45° to 45°.
To make it easier to set the mitre square, the
saw table has stops at 0°, 15°, 22.5°, 30° and
45°.
DANGER! Risk of injury due to
accidental switch-on!
Disconnect
the mains plug before carrying out
any work on the device.
Note:
The use of a swarf extractor is
recommended when processing
larger volumes.
DANGER! Risk of injury!
The prod-
uct must only be put into operation if
no defects are found. Ensure that any
defective parts are replaced before
the product is used again.
GB
temp.book Seite 14 Donnerstag, 7. April 2016 9:58 09
Summary of Contents for 380 335
