25
Inserting a tool
– Place the tool as far as it will go into the tool
holder (1).
– Close the front sleeve of the tool holder by turn-
ing anti-clockwise.
Selecting the operating mode
Use the switch for drilling/hammer drilling (2) to
select the operating mode as follows:
• Position
[
]
for hammer drilling in cement or
stone.
• Position
[
]
for drilling without the hammer
function into wood, metal, ceramics and plastics
and for the screwdriver function.
Changing the rotation direction
– To drill and screw screws into place, press the
rotation direction switch (4) to the left (rotation in
clockwise direction).
– To remove screws, press the rotation direction
switch to the right (rotation in an anti-clockwise
direction).
Check before switching on!
Check to make sure the device is in safe operating
condition:
– Check to make sure there are no visible defects.
– Check to make sure all device components are
correctly mounted.
Switching on and off
– To start the tool turning, press the On/Off but-
ton (5).
– To operate permanently, press the locking but-
ton (3) whilst holding the On/Off switch down.
– To release the lock, press the On/Off switch
again and release.
– To switch the unit off, release the on/off
switch (5).
Drilling
– Hold the device straight and drill with even pres-
sure.
Cleaning
Cleaning overview
Regularly and according to the operating condi-
tions
Troubleshooting
What to do when something doesn’t work…
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the
vendor. You will save yourself a lot of trouble and
possibly money too.
WARNING! Risk of injury!
Make sure that
when installing the tool that it fits securely
in the clamping chuck and is not at an
angle.
Note:
Clean and grease the shaft of the tool
before inserting.
NOTICE! Risk of damage to the unit!
Only change operating mode when the
device is switched off.
NOTICE! Risk of damage to the unit!
Do
not use setting
[
]
for screwing in and
removing screws.
NOTICE! Risk of damage to the unit!
Only use the rotation direction switch when
the device is at a standstill.
Note:
The revolution speed of the device
can be varied by applying different pres-
sures to the on/off switch.
DANGER! Risk of injury!
Never hold the
work piece that you are working with in your
hand, on your lap, or against other body
parts.
NOTICE! Risk of damage to the unit!
Never use the drill for chasing or to expand
drilled holes.
Always use a drill appropriate to the mate-
rial.
What?
How?
Clean the ventilation slots
of the motor to remove
dust.
Use a vacuum, cleaning
brush or paint brush.
Clean the device.
Wipe the unit with a damp
cloth.
DANGER! Exercise caution – risk of
injury!
Unprofessional repairs may mean
that your unit will no longer operate safely.
This endangers you and your environment.
Error/Fault
Cause
Remedy
Chuck is not turning.
No power supply?
Check the cable, plug, socket and the
fuse.
Is the device defective?
Contact your local vendor.
Wrong direction of rotation select-
ed?
Switch the rotation direction switch over.
Chuck is turning, but tool is not
drilling.
GB
Schlagbohrmaschine_380379.book Seite 25 Montag, 23. Januar 2017 12:19 12
Summary of Contents for 380379
Page 3: ...3 1 2 6 7 3 5 4 1 1 2 Schlagbohrmaschine_380379 book Seite 3 Montag 23 Januar 2017 12 19 12 ...
Page 81: ...81 Schlagbohrmaschine_380379 book Seite 81 Montag 23 Januar 2017 12 19 12 ...
Page 82: ...82 Schlagbohrmaschine_380379 book Seite 82 Montag 23 Januar 2017 12 19 12 ...
Page 83: ...83 Schlagbohrmaschine_380379 book Seite 83 Montag 23 Januar 2017 12 19 12 ...
