Lux Tools 389 828, Assembly And Operation Instruction

16

• Do not use the product if the steel cable is dam-

aged, knotted or twisted.

• Do not bend the steel cable or lay it over edges.
• Never couple several cable pulls.
• Never use the product to lift loads.
• Keep as far away from dirt as possible.

Personal protective equipment

Always wear the following safety equipment:

Preventing your clothing from being caught on 

something:

• Wear only close-fitting clothing!
• Do not wear any jewellery!
• If you have long hair, wear a hair net!

Your product at a glance

►

 P. 2, item 1

1.

Hook

2.

Ratchet lever

3.

Axle bolts

4.

Base frame

5.

Crank

6.

Steel cable

Unpacking

Unpacking the product and checking for complete-

ness.

Scope of delivery

• Cable pull unit
• Crank
• Small parts
• Instructions for use

Assembly

►

 P. 2, item 2

– Mount the crank (5) to the axle bolt (3) using the 

nuts provided.

– Unwind the steel cable until the screw holes in 

the base frame (4) are easily accessible 

(

►

 Winding/unwinding the cable without load – 

p. 16).

– Fasten the base frame to a solid and stable sur-

face using at least 3 screws/nuts (M10, not in 

scope of delivery).

Operation

Check before use!

Check the safety devices and the safe condition of 

the product:

– Check whether there are any visible defects.
– Check whether all parts of the product are firmly 

attached.

– Check that the safety devices are in faultless 

condition.

Moving or tensioning loads

Winding/unwinding the cable without load

►

 P. 3, item 3

– Place the ratchet lever (2) in the centre position.

The cable reel now moves freely in both directions.

– Pull the steel cable (6) at the fixed hook (1) until 

the hook can be attached to the load to be 

moved.

– Wind back in excessive cable by turning the 

crank (5) clockwise.

Winding up the cable under load (towing, loading)

►

 P. 3, item 4

– Hold the crank (5) firmly and push gently to 

relieve the ratchet lever (2).

– Place the ratchet lever (2) at Position 

[B]

.

Hand protection: Work gloves made of 

leather

DANGER! Risk of injury! 

Do not use a 

knife or sharp object to remove the adhe-

sive tape from the steel cable pulley!
The steel cable can be damaged.

Note: 

Make sure that the crank can still be 

completely turned following assembly.
If necessary, place a stable wooden board 

or a metal plate between base frame and 

assembly surface. Use screws long enough 

for fastening.

DANGER! Risk of injury! 

The product 

must only be put into operation if no 

defects are found. Ensure that any defec-

tive parts are replaced before the product is 

used again.

DANGER! Risk of injury! 

Check all 

mechanical components before use. Pay 

particular attention to material changes 

such as crack formations, deformations 

and material fractures.
If any component is faulty, the cable pull 

must not be used.

DANGER! Risk of injury! 

►

 P. 4, item 6

The steel cable must be visually checked 

for damage before each use. This damage 

can appear as shown in the illustration.
Products with damaged steel cable can 

cause serious injury.

NOTICE! Risk of product damage! 

The 

steel cable must not be laid around objects. 

Loads to be moved must not be hooked 

directly onto the steel cable. The hook must 

always be used to attach the load.

NOTICE! Risk of product damage! 

The 

steel cable must run evenly distributed on 

the pulley. Winding on just one side can 

cause the cable to jam and become dam-

aged.

GB

Seilzug_389828_389829.book  Seite 16  Dienstag, 12. April 2016  2:35 14