45
Cold starting the motor
– Slightly press fuel pump (16) approx. 3×.
– Position the throttle lever (18) in Posi-
tion
[
]
.
– Slow pull out the pull starter (11) until you
feel a resistance, then quickly and force-
fully, until the initial ignition noise can be
heard.
– Pull out the pull starter again quickly and
forcefully until the motor starts up.
– Allow the engine to warm up for approx.
10–15 seconds.
Switching off the motor
– Pull the fuel lever (5) into the back posi-
tion.
Mowing
Start the engine
Switch on the cutter
• The cutter may not move if the clutch
lever (6) is released.
• The clutch lever (6) can be actuated only
after the safety lock (7) is activated.
• Upon activation, the cutter (11) must start
running and stop upon release.
– Actuate the clutch lever (6) for cutter
slowly up to the limit stop.
– Hold the clutch lever (6) firmly during
operation.
Starting
– Slowly engage and firmly hold clutch
lever for travel guide (4) up to the stop.
Device starts.
Persistence
– Release clutch lever for travel drive (4).
Switching off the motor – p. 45
Information on mowing
• Steer the product at an even, slow speed
(walking pace) in the straightest lines
possible.
• Always work across slopes where possi-
ble.
• Do not cut wet grass if possible.
• Overlap the mowing lines slightly for an
even appearance.
Cleaning and maintenance
Cleaning and maintenance at a glance
Before each use
DANGER! Danger of fire!
Spilled
fuel can set the product on fire.
Carefully wipe up any spilled fuel up
before starting.
Start the product a minimum of nine
metres away from where you filled it.
Before starting, it must be guaran-
teed that none of the two clutch
levers can be actuated unintention-
ally.
Note:
In case of start-up difficulties,
please refer to the following able:
Note:
Pull the pull-starter max. 50
cm out and let it run back in slowly by
hand.
WARNING! Risk of injury!
Always
switch off the product when not in
use for short periods.
CAUTION! Risk of injury!
NOTICE! Risk of product damage!
Allow the engine to run warm before
starting up.
Ensure that the respective ventilation
slots (15) do not get clogged with cut
material and as such the engine is no
longer cooled sufficiently.
Note:
Allow engine to run for few
minutes for drying before starting up.
WARNING! Risk of injury!
Always
switch off engine before all cleaning
and maintenance work, allow device
to cool down and remove ignition
cable.
What?
How?
Check cable of the
pull-starter for
damage
Visual inspection.
Check motor oil
level
Check screw con-
nections are tight
Hand-tighten the screw
connections using the
appropriate tool.
GB
Balkenmaeher_468426.book Seite 45 Mittwoch, 6. April 2016 3:14 15
Summary of Contents for 468 426
