LUX 389842, Original Instructions Manual

10

– Insert the jet pipe for low pressure (8) into con-

necting pipe (7) and rotate by approx. 90° until 
the two parts are securely connected (bayonet 
connection).

– Remove the cleaning agent container (1) from 

the holder.

– Fill the storage tank (1) with cleaning agent.
– Place the container in the holder and close the 

lid.

– Set the jet pipe by adjusting the nozzle (22) to 

low pressure.

– Switch on the machine.
– Spray the cleaning agent onto the dry surface 

and let it soak (do not let dry).

– Set the jet pipe by adjusting the nozzle (22) to 

high pressure.

– Use the high-pressure jet to rinse off any loos-

ened dirt.

Cleaning and maintenance

►

 P. 6, item 18, 

►

 P. 6, item 19

Overview of cleaning

Regularly, depending on conditions of use

Cleaning the water filter

– Remove the plug-in coupling for the water con-

nection (13).

– Remove the water filter (18) from the plug-in 

coupling and clean using water.

– Remove contamination from the nozzle opening 

using the needle provided and flush from the 
front with water.

Clean the high-pressure jet nozzle

– Clean the nozzle by carefully inserting a needle 

provided, or a thin and sharp instrument (i.e. 
paperclip) into the nozzle to rid it of debris. Any 
fine debris will cause the nozzle hole to become 
clogged.

– Flush the debris out of nozzle by back flushing 

(running the water through the nozzle backwards 
or from the outside to the inside).

– Make sure all the debris have been cleaned or 

knocked out of the nozzle.

Storing, transport

Storing

– Store the machine where it is dry and well venti-

lated.

– When placing the machine out of service for an 

extended period of time, remove the cleaning 
agent and drain all the water left in the hoses.

Transport

– If shipping, use the original packaging wherever 

possible.

Malfunctions and troubleshooting

In the event of a malfunction…

Malfunctions are often caused by minor faults. You 
can easily remedy most of these yourself. Please 
consult the following table before contacting the 
vendor. You will save yourself a lot of trouble and 
possibly money too.

DANGER! Risk of injury! 

Before carrying 

out any work on the product, ensure that 
the mains plug is pulled out of the mains 
socket and the product is depressurised.

What?

How?

Clean the machine.

Wipe the unit with a 
slightly damp cloth Do 
not clean the machine us-
ing a high-pressure water 
jet.

Clean the high-pressure 
jet nozzle.

►

 Clean the high-pres-

sure jet nozzle – p. 10

NOTICE! Risk of machine damage! 

Fro-

zen residual water may damage the 
machine! If there is a danger of frost, store 
the machine including all accessories in a 
place protected from frost.

DANGER! Risk of injury! 

Improperly con-

ducted repairs may prevent your machine 
from working safely. Such repairs will 
endanger you and your surroundings.

Fault/malfunction

Cause

Remedy

Machine is not running.

Machine is faulty?

Contact your local vendor.

No mains voltage?

Check cables, plug, socket and 
fuse.

On/Off switch set to 

[0]

?

Switch on the machine.

No or only little pressure is built up. Air in the system?

Ventilate the machine! Run the ma-
chine without the high-pressure 
hose connected until water starts 
leaking without bubbles. Re-attach 
the high-pressure hose.

Leaks?

Check all inlet pipes leading to the 
pump for leaks or clogs.

Setting of the high-pressure jet noz-
zle?

Check the setting on the hand-held 
spray gun.

►

 Adjusting the high-pressure wa-

ter jet – p. 9

GB

temp.book  Seite 10  Donnerstag, 7. April 2016  9:55 09