Fold
Fold
Fold
2
Preparing for Access
IP Addressing
If the XWC-1000 is connected to a network with a 192.168.0.X address
scheme, and your computer shares a similar address on the same network,
you can skip to the next step,
Getting Connected
.
n
Note:
Be sure a DHCP server is present on the network and
that all Luxul APs and the XWC-1000 Wireless Controller will
share the same subnet.
If your network doesn’t use a 192.168.0.X IP address scheme, you will need
to manually change the IP address of your computer to be able to config-
ure the XWC-1000 Wireless Controller so that it is on the same subnet as
your network. For help setting the IP address of your particular operating
system, visit
luxul.com/ip-addressing
.
3
Getting Connected
Access the Setup Wizard by opening your web browser and enter the Wireless
Controller’s default 192.168.0.19 IP address in the address field. Log in to the
Wireless Controller using the default user name and password:
Default IP: 192.168.0.19
Username: admin
Password: admin
c
Caution:
If there is another device on the network already
using the 192.168.0.19 address, you’ll need to either temporarily
disconnect or reconfigure that other device, or manually
configure the Wireless Controller with a different address
on a separate isolated network.
4
Wireless Controller Configuration
Follow the built-in Setup Wizard in the Wireless Controller. The Wizard will walk
you through creating a configuration profile, then it will automatically configure
and manage all available APs on the same network. You may add or remove APs
to or from the managed profile at any time.
t
Smart Tip:
For more information on setup and configuration
best practices, visit
luxul.com/smart-tips
.
5
Hardware Operation - Wireless Controller
Selecting front-panel LED color
Use the switch on the rear panel of the XWC-1000 Wireless
Controller to switch the Power and System LEDs on the
front panel between green and blue to best match the
equipment in the rack where the Wireless Controller is
sharing space.
Resetting the Controller
X
Reset/Reboot:
Use a paper clip to briefly press and
release the Reset button on the rear panel of the
Controller to force it to reboot. The front panel LEDs will
go dark once the button is released, then the System LED
will blink slowly while the controller reboots.
X
Restore Factory Defaults:
To restore the controller to Factory Default
configuration, press and hold the Reset button for at least 5 seconds. The
System LED will blink quickly to indicate that the Controller is returning to
Factory Default configuration, go dark for a few seconds, then blink slowly
while the controller boots.
X
Normal Operation:
When the controller is operating normally, the System
LED will blink like a heartbeat, i.e. blink-blink-pause.
c
CAUTION:
Pressing and holding the Reset button will restore
the Wireless Controller to factory default and
remove any custom configuration.
5
Hardware Operation - Wireless Access Points
LED Indicators
If the green power LED is ON, the XAP-810 is working. If
the Power LED is OFF, the AP is not receiving power or
the LED has been turned off in the AP’s web interface.
If the power LED is blinking, the XAP-810 is booting. The
two blue LEDs indicate indicate each of the 2.4GHz and
5GHz networks are configured and broadcasting.
Reset Button:
The Reset button is located underneath the mount and
marked RESET. It may be used to reboot the AP or to
restore factory default settings.
To Reboot the AP: With the XAP-810 powered on, simply
press and release the Reset button.
To Restore the Default Settings: With the XAP-810 powered on, press and
hold the Reset button for at least 5 seconds. Release the button, the LED
will flash rapidly and the XAP-810 will be set to factory defaults.
c
CAUTION:
Pressing and holding the Reset button will restore
the AP to factory default and remove any custom
configuration.
PoE Injector:
If the Green ON LED is illuminated, power is connected to the
injector. If the ON LED is not lit, the injector is not receiving power.
