11
Operation
Control functions
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
SLi
SPr
Coin-op mode + remote start
Press <
2
> 1x to start the appliance.
Stand alone mode
Press <
2
> 1x.
The display shows the maximum tanning time (start time). Use the <
14
> and <
15
> keys to change the tanning time.
Pause mode
Press <
3
> 1x during a tanning session to put the appliance into pause mode. The lamps will switch off. The body
cooling will continue operating (maximum 4 minutes). Xsens (optional) and Qsens (optional) will pause.
Press <
2
> 1x to confirm the chosen time. The appliance will switch on and the tanning time will start.
While in pause mode press <
2
> 1x to switch the sunbed on again or press <
3
> 1x to switch the sunbed off. This will
stop the tanning session and the sunbed wil start the mandatory 3-minute cooling off period.
The display will continue to show the tanning time left and the message “PRESS START TO RESUME” will scroll across
the bottom.
Note:
Tanning time will continue to elapse when the appliance is in pause mode.
If the sunbed is switched back on within 4 minutes after pressing <
3
>, the face tanner (only SLi) will not switch on. The face
tanner will restart automatically after a mandatory 4-minute cooling off period.
If the <
3
> button is pressed, the airco (option) will switch off after a 5 minute delay. Following these 5 minutes, the airco also
has a cooling down period of 3 minutes.
Summary of Contents for X7
