background image

Rev #5 

Version 1.01

 

July 

2020

 

 

 

Page 6 of 

34

 

1.2

 

General information about FLARM  

For years, general Aviation has been confronted  with dramatic mid-air collision accidents. 

With  the  extreme  fine  shape  and  relatively  high  cruise  speed  of  modern  airplanes, 

the 

human vision  has reached its limit of detection. Another aspect is airspace restrictions for 

VFR traffic that create an augmentation of traffic density in certain areas, and the associated 

airspace complexity that

 

requires more pilot attention to the n

avigation material. These have 

a direct impact on the probability of a collision  affecting powered aircraft, gliders, and 

rotorcraft operations. 

 

This type of equipment in General Aviation is not required by technical specifications or by 

operational  regulations but  is recognized by the regulators as an important step toward 

improved aviation safety. Therefore, it is not considered as essential for flight and may be 

used for 

situation awareness only

 on basis of non-

interference with certified equipment 

necessary for safe flight and no hazard to persons on board. 

A  correct  antenna installation has a great effect on the transmission/receiving range. The 

pilot shall ensure that no masking of the antenna occurs, especially when the antennas are 

located in the cockpit. 

 

FLARM wi

ll  only  warn  about  other  aircraft  that  are  likewise  equipped  wit

h a compatible 

device. 

 

The firmware must be updated to the la

test version at least every 12

 months. Failure to do 

so can lead to the device not being able to communicate with other aircraft or not operate at 

all. 

 

By using FLARM you agree to the 

End User License Agreement (EULA)

 and 

Terms of 

use of FLARM

  (part of th

e  EULA)  valid  at  time  of  use.  This  can  be  found  in  the  next 

chapter. 

1.3

 

Flarm end user license agreement 

This section contains the End User License Agreement issued by FLARM Technology Ltd, 

the licensor of FLARM devices.

 

 

 

END USER LICENSE AGREEMENT 

 

By purchasing or using a FLARM device or by downloading, installing, copying, accessing, or 

using any FLARM Technology Ltd, Cham, Switzerland (hereafter "FLARM Technology") 

software, firmware, license key, or data, you agree to the following terms and conditions. If 

you do not agree with the terms and conditions do not purchase or use the FLARM device 

and do not download, install, copy, access, or use the software, firmware, license key, or 

data. If you are accepting these terms and conditions on behalf of another person, company, 

or other legal entity, you represent and warrant that you have full authority to bind that 

person, company, or legal entity to these terms and conditions. 

Summary of Contents for TrafficView



































Reviews: