TD-40, TD-75
SHAFT ASSEMBLY INSTALLATION:
Holding the shaft assembly by the threaded shaft only (not brass stud) install center stud spring onto shaft assembly (end opposite
pinned nut). With spring end up, insert the shaft assembly through the center tube and Tumble-Dump plate until brass stud contacts
center tube. Apply Loctite® onto brass stud and screw into center tube - approximately 4 turns - until wrench flats on brass stud are
flush with center tube. Set aside to dry.
BOWL ASSEMBLY:
Place the bowl over the center hole and screw the shaft assembly into the motor plate and back off two turns. Install bowl washer and
fasten with the 1-8 nut and tighten. With the wrench provided, tighten the shaft assembly to obtain the desired operating tightness.
TUMBLE-DUMP FEATURE:
Raytech's Tumble-Dump models (TD-40 and TD-75) feature a built-in hinge system that allows the parts and media to be easily
removed from the machine. Used with a Raytech Separator (MS-75) the Tumble-Dump saves time and money by eliminating the
tedious tasks of unloading and separating by hand. With the special 3/4" hex wrench provided, loosen the 3/4" hex nut until the shaft
and nut spring up - approximately 6 turns. This will release the tumble-dump plate and bowl assembly from the motor plate. Raise the
dump handle to dump media and parts. To secure, return the tumble-dump plate and bowl assembly to the "run" position. With the
special wrench provided, compress the internal spring by pushing down on the 3/4" hex nut and turn to engage threads into the
motor plate. Tighten securely.
NOTE: Occasionally lubricate lower shaft assembly threads and motor plate threads with a light grease such as “Lubri-Plate.”
1
2
3
4
5
6
7
8
9
10
12
13
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
15
ITEM
PART NO.
DESCRIPTION
QTY
1
07968
Shaft Assembly TD-40
1
1
07966
Shaft Assembly TD-75
1
2
07943
Cover Wing/Perm Nut Assembly
1
3*
23032
Bowl with Cover AV-40
1
3**
23046
Bowl with Cover AV-75
1
4
03376
Nut 1” -8 Hex Full Zc
1
5
07925
Bowl Holddown Plate
1
6
07883
Center Stud Spring
1
7
08377
Tilting Plate TD-40
1
7
07933
Tilting Plate TD-75
1
8
07796
Top Pad Cut (Not Shown)
1
8a
07779
Rubber Pad
5
9
03299
Hex Head Screw 5/16 - 18 x 1 1/2
6
10
07773
Motor Plate
1
12
07941
Compression Spring
6
13
07942
Spring Grommet
12
14
03243
Washer 5/16 USS STD
12
15
03349
Nut 5/16-18 Hex Zc
6
16
03284
Hex Head Screw5/16-18 x 1 1/4
6
17
07942
Spring Grommet
12
18
03480
Carriage Bolt 3/8-16 x 8” Long
4
19***
30255
Motor 40/75 110V
1
19***
30293
Motor 40/75 230V
1
20
03325
Jack Nut Molly #10-24
4
21
07772
Motor Bar
1
22
03388
Nut 3/8-16 Locking
4
23
07972
Counterweight Assy
1
24
07784
Bottom Cover
1
25
03440
Screw #8 x 3/8 Typ A Pan
3
26
07882
Rubber Feet
3
27****
07782
Base Model 40
1
27****
07783
Base Model 75
1
28
07941
Compression Spring
6
29
03462
Screw #10-32x3/8 Pan Zc
3
30
07781
Strap for Capacitor
1
31
03928
Capacitor 115V R
1
31
03927
Capacitor 230V R
1
32
03065
Screw 1/4-20 x 1 1/4 Hex Zc
4
33
07923
Hinge Pivot Block
2
34
07770
Hinge Bar
1
35
07920
Tilting Hinge
2
36
07909
Strainer Fitting
1
37
03374
Nut 3/4-16 Jam Zc
1
38
03055
Screw 1/4-20 x 3/4 Hex Zc
4
39
07936
Drain Tube 3/8 LD x 30” S/A
1
*Includes 36,37,39 (Not Shown)
**Includes 36,37,39 (Not Shown)
***Includes 8,8a,9,10,13,14,15,18,19,21,22,29
****Includes 14,16,17,20,24,25,26,27
32
33
34
35
36
37
38
