background image

Reference Manual D VD 5002 Version1.1

 

 

Page 19  

 

 

Available Options 

Below is a list of related products for the D VD 5002 
CardModule. Please refer to product brochures or 

our web site for more detailed information. 

 

  Model                            Description 

  

R FR 5010 

 

Series 5000 Rack Frame (empty) with single 
power supply 

 

  

R PS 5010 

 

Redundant power supply for the R FR 5010 
Card Frame 

 

 

R CT 5020 

 

Rack controller for the R FR 5010 Card 
Frame  

 

 

R CT 5010 

 

Rack Bus Extension for the R FR 5010 Card 
Frame. In combination with R CT 5020 

 

 

Parts List 

 
Due to the very dense design and miniature 

surface mount technology the module is not field 

serviceable. The information for a replacement 
assembly is below. 

 

D VD 5002 CardModule (complete) 

Description 

 

Dual SDI DA w/ monitoring 

Model Number 

D VD 5002 

Part Number   

6.155.008.235 

 

Sub Assemblies: 

 

D VD 5002 Processing Board only (BS 5013)   

Part Number   

6.155.010.211 

 

Rear Connection Panel for D VD 5002 (MA5001_B) 

Part Number    

6.155.008.371 

 

Summary of Contents for D VD 5002























Reviews: