manualshive.com logo in svg

Lynx RADIEN Crossover E-TEC Series, Operator'S Manual

The Lynx RADIEN Crossover E-TEC Series comes with an Operator's Manual for easy set-up and operation. Download the manual for free from our website to ensure you get the most out of your Lynx product. Enjoy seamless performance and high-quality results with the help of our comprehensive user manual.

Share
Download
background image

TABLE OF CONTENTS

FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1

Know Before you Go . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

Safety Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

About this Operator's Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4

SAFETY INFORMATION

GENERAL PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Avoid Carbon Monoxide Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Avoid Gasoline Fires and Other Hazards. . . . . . . . . . . . . . . . . . . . . . . 12
Avoid Burns from Hot Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SPECIAL SAFETY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

RIDING THE VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Pre-Ride Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How to Ride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Carrying a Passenger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Terrain/Riding Variations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

TRACTION ENHANCING PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Manoeuvrability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Braking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Important Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Effects of Having a Studded Track on the Life of the
Snowmobile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installation of Studs on BRP Approved Tracks. . . . . . . . . . . . . . . . . 42
Maintenance/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SAFETY INFORMATION ON THE VEHICLE . . . . . . . . . . . . . . . . . . . . . 46

Hang Tag(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Vehicle Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Technical Information Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

VEHICLE INFORMATION

CONTROLS, INSTRUMENTS AND EQUIPMENT. . . . . . . . . . . . . . . 64

Handlebar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Throttle Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Brake Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Parking Brake Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

__________________

5

Summary of Contents for RADIEN Crossover E-TEC Series




























































































































































































































































































Reviews:

No comments

Related manuals for RADIEN Crossover E-TEC Series

Club Car 2007 XRT 800 Maintenance Service Manual preview
2007 XRT 800
Brand: Club Car Pages: 516
Hisun HS 200UTV-2 Owner'S Manual preview
HS 200UTV-2
Brand: Hisun Pages: 57
Taylor-Dunn B0-012-10 Operation, T Roubleshooting And Replacement Parts Manual preview
B0-012-10
Brand: Taylor-Dunn Pages: 254
E-TON 2006 Viper 70 Owner'S Manual preview
2006 Viper 70
Brand: E-TON Pages: 36
Yamaha ET340ED Supplementary Service Manual preview
ET340ED
Brand: Yamaha Pages: 13
Yamaha EX440D Supplemental Service Manual preview
EX440D
Brand: Yamaha Pages: 14
Yamaha ET340D Supplementary Service Manual preview
ET340D
Brand: Yamaha Pages: 13
Yamaha G-Max G22A Owner'S And Operator'S Manual preview
G-Max G22A
Brand: Yamaha Pages: 47
Yamaha CAMSO Installation Manuallines preview
CAMSO
Brand: Yamaha Pages: 16
Yamaha GRIZZLY 125 YFM125GY Owner'S Manual preview
GRIZZLY 125 YFM125GY
Brand: Yamaha Pages: 130
Yamaha GRIZZLY 125 YFM125GZ Owner'S Manual preview
GRIZZLY 125 YFM125GZ
Brand: Yamaha Pages: 132
Yamaha G1AM4 Owner'S/Operator'S Manual preview
G1AM4
Brand: Yamaha Pages: 100
Yamaha DRIVE 2 2022 Owner'S/Operator'S Manual preview
DRIVE 2 2022
Brand: Yamaha Pages: 64
Yamaha GRIZZLY 125 YFM125GD Owner'S Manual preview
GRIZZLY 125 YFM125GD
Brand: Yamaha Pages: 134
Yamaha GRIZZLY 125 YFM125GA Owner'S Manual preview
GRIZZLY 125 YFM125GA
Brand: Yamaha Pages: 132
Yamaha FX Nytro Owner'S Manual preview
FX Nytro
Brand: Yamaha Pages: 104
Yamaha EC340M 1988 Owner'S Manual preview
EC340M 1988
Brand: Yamaha Pages: 124
Yamaha FX Nytro FX10MTRAX Assembly Manual preview
FX Nytro FX10MTRAX
Brand: Yamaha Pages: 152

Brands by name

Popular brands

Load more brands