Lynxmotion HQuad500 Assembly Manual Download | Manualshive

Page: 9 / 16

background image

Lynxmotion UAV

HQuad500 Frame Assembly Guide

2.4 - Electronics

At this stage it is the best time to mount the electronics before closing the two frame halves and add the arms. Since
the ESC (electronic speed controller) will be mounted inside the frame we also recommend to test motor rotation for
each arm location based on your flight controller recommendations.

We provide ESC mounting plates that act as a frame stiffener as well. The ESC’s are held on the plate with 3” Cable
ties.

Lynxmotion UAV HQuad500 Side Plate (for ESC’s)

Lynxmotion UAV

P.9

«
...
7
8
9
10
11
...
»

Summary of Contents for HQuad500

















Reviews:

No comments

Related manuals for HQuad500

X4 Quadcopter 550 SPY

Brand: Carson Pages: 40

Brand: Aovo Pages: 38

Brand: Ares Pages: 12

TRIPLTEK LIFTHOR LITE

Brand: Thor’s Drone World Pages: 13

Brand: FIELD OF VIEW Pages: 24

AirDrope Series

Brand: FLIFLI Pages: 17

Brand: Foxtech Pages: 8

ARROW DSH-SRD2-P4-3

Brand: Drone Sky Hook Pages: 2

Brand: Drone Sky Hook Pages: 3

Brand: DRONExpert Pages: 7

Brand: Drone Sky Hook Pages: 7

PIONEER UFO 509

Brand: DRONE-HOBBY Pages: 10

Drone X Pro Xtreme

Brand: Drone-Clone Xperts Pages: 11

Brand: Drone Sky Hook Pages: 12

Brand: Drone Sky Hook Pages: 17

Brand: Drone Sky Hook Pages: 28

Brand: Drone Rescue Systems Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands