background image

 

      

 

 

 

Only a properly qualified technician should install and maintain the DC3P or its accessories.  Any electrical work should be 
performed only by an ASE certified (minimum T6 & L2) technician with an expertise in installing and troubleshooting advanced 
vehicle onboard components including multiplexed circuits. Lytx, Inc. disclaims all responsibility for any damages arising from 
improper installation and maintenance of the DC3P or its accessories. 

© 2016 Lytx, Inc. – Confidential & Proprietary 

This guide is protected as confidential and proprietary information of Lytx, Inc.  Copying and use of this guide for any purpose 
other than installing DC3P or its accessories in vehicles of Lytx, Inc.’s customers is expressly prohibited.  Information contained in 
this guide was in effect as of the date set forth above and is subject to change without notice or liability.  Lytx, Inc. reserves the right 
to revise the information presented or to discontinue the production of parts described at any time. 

 

Lytx

®

DC3P Event Recorder 

Installation Guide 

Last Updated: November 28, 2016 

© 2016 Lytx, Inc. 

Summary of Contents for DC3P





























Reviews: