background image

FES Maintenance manual Version 1.12  

September 2016 

Page 12 of 26 

 
4. FES maintenance  

 

4.1 Maintenance of main FES components 
 
4.1.1 Motor maintenance 
 

FES motor is designed so that practically does not need any special maintenance.  

 

Warning:

 

Opening or disassembling of the motor would cause a forfeit of 

warranty claims! It could be also very dangerous, due to very strong magnets 
on rotor!

 

 

Though, it has to be considered that no foreign objects at all can enter the interior 

of the drive. Further, it is necessary to protect the motor from humidity, dirt, paint, glues 
etc. If this is ignored, a proper functionality of the motor can not be guaranteed and 
irreparable damages are possible. In case of damage, ship the motor back to the 
manufacturer for repairs. Unintended handling leads to secondary damages. 

 

Note:

 

Keep magnetic memory cards or electronic devices out of the rotor’s 

close-up range, because the strong magnetic field can cause a delete of data. 
Be also careful with medical devices (e.g. pacemakers) which might be 
sensitive to strong magnetic fields.

 

 

The small gap between the stator and the magnets of the rotor function-bound has 

a thickness of only a few tenth millimeters. Here, the danger of foreign objects 
accumulating in this gap exists but can be heard by scratching-sounds. In this case 
spinner should be removed and the motor should be blown-out with compressed air. Do 
not at all simply keep on using the drive. Be especially aware of cuttings which can almost 
irremovably stick to the magnets. In this case, the only thing that helps is a disassembly of 
the drive by the manufacturer. 

 

4.1.2 Propeller maintenance 
 

Please refer to FES Propeller manual about. 

 
4.1.3 Battery packs maintenance 
 

Please refer to FES Battery pack manual. 

 
4.1.4 FCU instrument maintenance 
 

Please refer to FES FCU manual. 

 
 
 

Summary of Contents for AS 13



























Reviews: