background image

FES Maintenance manual Version 1.12  

September 2016 

Page 3 of 26 

 

1. Important notices 

 

Please  read  this  manual  thoroughly.  It  contains  important  information  about  FES 

system and its maintenance, having a vital importance to the flight safety.  

Information’s in this document are subject to change without notice. LZ design 

reserves the right to change or improve their products and to make changes in the content 
of this material without obligation to notify any person or organization of such changes or 
improvements.  
 

1.1 Limited Warranty  
 

This FES system is warranted to be free from defects in materials or workmanship for 

two years from the date of purchase when installed by LZ design. Within this period, LZ 
design will, at its sole option, repair or replace any components that fail in normal use. 
Such repairs or replacement will be made at no charge to the customer for parts and 
labor, however the customer shall be responsible for any transportation cost. This 
warranty does not cover failures due to abuse, misuse, accident, or unauthorized 
alterations or repairs.  

 
I case that FES is installed to the sailplane by authorized Company, the Company 

carries also responsibility and warranty for installation and failures of components, which 
could be result of improper installation even if they occur later during normal use (if the 
cause of a failure is with wrong installation). LZ design will not cover failures due to 
unauthorized installation, alterations or repairs, abuse, misuse, or accidents.

 

 

THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN 

LIEU OF  
ALL OTHER WARRANTIES EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING ANY  
LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU  
SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. 
  
IN NO EVENT SHALL LZ DESIGN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT 
OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR  
INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do  
not allow the exclusion of incidental or consequential damages, so the above limitations 
may not apply to you. LZ design retains the exclusive right to repair or replace the unit or 
software, or to offer a full refund of the purchase price, at its sole discretion. SUCH 
REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF 
WARRANTY.  
 

To obtain warranty service, contact your local LZ design dealer or contact LZ design 

directly.  
 
October 2013  

 

 

 

 

© 2013 LZ design. All rights reserved 

 

Summary of Contents for AS 13



























Reviews: