background image

15 

To ensure the feasibility of the cable routes, it is suggested that the cables be 
run prior to installation of the radio.  Ensure slack is left in each cable so the 
radio may be removed for servicing with all connections remaining intact. 

D3100 is intended for installation within a weatherproof building, enclosure, 
or vehicle. Typical installations are: 

1.

 

Elevated (usually beyond unassisted reach) in an outside enclosure with 
co-located antenna, 

2.

 

Mounted inside a building and connected by RF cable to outside antenna 
(usually above unassisted reach), or 

3.

 

Vehicle installation with vehicle rooftop antenna. 

Install the D3100 so that the LED indicators on the front panel are visible 
during operation. 

If installation is within the United States, it is recommended the unit be 
installed by one of the many M/A-COM Authorized Service Centers located 
throughout the U.S.  Personnel at these centers are experienced in installations 
of this type and can provide a safe, neat, and functional installation. 

6.3 

INSTALL D3100 RF MODEM 

Mount the antenna, following the included instructions, in a manner that 
prohibits or precludes the presence of anyone within the prescribed MPE 
Radius when the transmitter is on (see Table 1-1). Connect the antenna to the 
D3100 antenna connector. 

In order for the D3100 to communicate with the RS-232 device, the D3100 
data cable must be connected to the RS-232 device using an appropriate data 
cable or cable adapter. The

 

accessory

 

Data/Programming/C-U Adapter Cable 

(CA103067V1) that comes with the D3100 provides this interconnect 
function. When assembling hand-made adapters, make sure the corresponding 
function is connected between the D3100 Data Cable and other devices. 
Connection of non-corresponding (dissimilar) functions may cause damage to 
the D3100 or connected equipment and/or failure of proper performance. (See 
Section 4.1 for the data connector functions.) 

Connect the polarized power plug of the D3100 power cable to a 
corresponding polarized socket on a 13.6 +/-15% DC, regulated power 
supply, the Red lead to positive (

+

) and Black lead to negative or ground (

-

). 

When power is on, the Yellow LED is on. 

If the correct personality has been entered, correct data connection, antenna 
connection, and power connection are made, and power is on, then D3100 is 
ready for data calls. 

Summary of Contents for P5100 Series























Reviews: