background image

IMPORTANT SAFETY INSTRUCTION

1. READ 

INSTRUCTIONS 

 

 All the safety and operating instructions should 
be read before the appliance is operated. 

2. RETAIN 

INSTRUCTIONS

 

  The safety and operating instructions should be 
retained for future reference. 

3. HEED 

WARNINGS

 

 All warning on the appliance and in the operating 
instructions should be adhered to. 

4.  

FOLLOW INSTRUCTIONS

 

 All operating and use instructions should be 
followed. 

5. WATER 

AND 

MOISTURE

 

 The appliance should not be used near water – 
for example, near a bathtub, washbowl, kitchen 
sink, laundry tub, in a wet basement, or near a 
swimming pool, etc. 

6. CARTS 

AND 

STANDS

 

 The appliance should be used only with a cart or 
stand that is recommended by the manufacturer. 

6A.

    An appliance and cart combination should be moved 

with care. Quick stops, excessive force, and uneven 
sTurfaces may cause the appliance and cart 
combination to overturn. 

7. 

WALL OR CEILING MOUNTING

 

 This equipment is not designed 
for use mounted on a wall or a 
ceiling. 

8. VENTILATION

 

 The appliance should be situated so that its 
location or position does not interfere with its 
proper ventilation. For example, the appliance 
should not be situated on a bed, sofa, rug, or 
similar surface that may block the ventilation 
openings, or places in a built-in installation, such 
as bookcase or cabinet that may impede the flow 
of air through the ventilation openings. 

 

 At least 30 cm free space around the unit for 
normal ventilation is required. 

9. HEAT

 

 Do not install near any heat sources such 
as radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce 
heat. 

10. CLEANING

 

 The appliance should be cleaned only with dry 
cloth. 

11. POWER 

SOURCES

 

 The appliance should be connected to a power 
supply only of the type described in the operating 
instructions or as marked on the appliance. 

12.  POWER CORD PROTECTION

 

 Power-supply cord should be routed so that they 
are not likely to be walked on or pinched by items 
placed upon or against them, playing particular 
attention to cords at plugs, convenience 
receptacles, and the point where they exit from 
the appliance. 

13. POLARIZED 

PLUG

 

   Do not defeat the safety purpose of the polarized 

or grounding-type plug. A polarized plug has 
two blades with one wider than the other. A 
grounding type plug has two blades and a 
third grounding prong. The wide blade or the 
third prong are provided for your safety. When 
the provided plug does not fit into your outlet, 
consult an electrician for replacement of the 
obsolete outlet. 

14.  UNPLUG POWER CORD

 

 Unplug this apparatus during lightning storms or 
when unused for long periods of time. 

15.  OBJECT AND LIQUID ENTRY

 

 No object filled with liquids, such as vases, etc. 
shall be placed on the apparatus. 

16. ACCESSORIES

 

 Only use attachments/accessories specified by 
the manufacturer. 

17. SERVICING

 

 The user should not attempt to service the 
appliance beyond that described in the operating 
instructions. All other servicing should be referred 
to qualified service personnel. 

18.  DAMAGE REQUIRING SERVICE

 

 The appliance should be serviced by qualified 
service personnel when: 

 a) 

 

 

The power-supply cord or the plug has been 
damaged; or

 b) 

 

  Objects have fallen, or liquid has been spilled 

into the appliance; or

 

c)  The appliance has been exposed to rain; or

 d) 

 

  The appliance does not appear to operate 

normally or exhibits a marked change in 
performance; or

 e) 

 

 

The appliance has been dropped, or the 
enclosure is damaged. 

Summary of Contents for SBX10


















Reviews: