background image

 

MAN465 

 

Rev. 1.1 

11 

8

 

Regulatory Information 

 

Federal Communication Commission (FCC) Compliance Statement 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. This 

equipment generates uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one of the following measures: 
 

▪ Reorient or relocate the receiving antenna.

 

 

▪ Increase the separation between the equipment and receiver. 

 

  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.  

 Consult the dealer or an experienced radio/TV technician for help.  

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired 

operation. 

 
Industry Canada (IC) Compliance Statement 

This device complies with Industry Canada license exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause 

undesired operation of the device.  
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils 

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) 

l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter 

tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en 

compromettre le fonctionnement.

 

 

 

Summary of Contents for VoltTab














Reviews: