M-Robot M-388 Operating Manual Download

Page: 6 / 16

5. When wrong start button is pressed, the other start switch needs to be pressed twice

before cleaning.

6. The max working time for the Cleaner is about 60 minutes, which can meet the

requirements for cleaning a normal room. If the battery power is about to run out, the

battery life indicator will become red, and it will stop working. Charging of battery is

needed.

Please see the following drawing for operating
the Virtual Wall Unit:

Virtual Wall Unit uses two (1# dry battery) to divide the infrared emission distance into

three gears as following drawing:

Do not use the infrared wave emitter to point at the eyes!

Infrared wave emitter

Power switch

Power Indicator

Range Selector Switch

INTELLIGENT CLEANER

OPERATING MANUAL

You can select according to your cleaning

condition.

over 7M
3-7 M
0-3 M

Refer to the following drawing for charging method
and use of auto charging socket:

Signal sensor

Function setting key

LCD display

Charging touch plate

Caution

- 5 -

Summary of Contents for M-388

















Search results

Summary of Contents for M-388

Reviews:

Related manuals for M-388

Brands by name

Popular brands

M-Robot M-388, Operating Manual

Search results

Summary of Contents for M-388

Reviews:

Related manuals for M-388

Brands by name

Popular brands