24
GB
461308128_GB-ES (001)_04/2013
ADJUSTMENTS
• Always disconnect the appliance from
the electricity supply before making any
adjustment.
• All seal must be replaced by the technician
following any adjustment or regulation.
• The adjustment of the reduce rate (simmer)
must be undertaken only with burners
functioning on natural gas while in the case of
burners functioning on L.P.G, the screw must
be locked down fully (in clockwise direction).
• “Primary air adjustment” on hob gas burners
is unnecessary.
TAPS (fig. 21)
All gas taps are male cone type with only one way of
passage. The adjustment screw (V) is on the side of
the stem.
Adjustment of the
“Reduced rate”
position as follows:
l• Turn the burner on and place the knob on the
“Reduced rate” position (small flame).
• Remove the knob of the tap which is attached by
simply applying pressure to the rod.
• With a small screwdriver (C) turn to the right or
left the adjustment screw (V) until the flame of
the burner is conveniently regulated to the Low
position.
• Check that the flame does not go out when the knob
is sharply switched from the “Full on” to “Reduced
rate” positions.
�
�
�
�
21
22
O
VEN THERMOSTAT (fig. 22)
Reduced rate adjustment
should be carried out in
the following way:
• Remove the knob thermostat.
• Switch on the oven burner by turning the relative
knob to the Maximum position, then wait about 10
minutes.
• Slowly turn the knob back to the Minimum position
and, using a small screwdriver (C), turn screw (V) to
the right to lower the flame or to the left to increase it.
The flames must be short for an efficient Reduced
rate setting. They must be stable to prevent them
from accidentally going out and must be able to
stand up to normal oven door manoeuvres.
OVEN BURNER (fig. 23)
The burner is installed on the oven base and is covered
by the bottom plate which must always remain in that
position during oven operation,
To adjust the primary air,
light the burner and,
watching the flame, slacken screw (A) and adjust
sleeve (B) to obtain the X openings indicated in the
table see on paragraph «
TECHNICAL FEATURES
».
Lock screw (A) in place once the adjustments have
been made.
GRILL BURNER (fig. 24)
To adjust the primary air,
light the burner and,
watching the flame, slacken screw (A) and adjust
sleeve (B) to obtain the X openings indicated in the
table see on
paragraph «TECHNICAL FEATURES»
..
Lock screw (A) in place once the adjustments have
been made.
INSTRUCTIONS FOR THE INSTALLER
Downloaded from www.vandenborre.be
Summary of Contents for MFTW95IX
