background image

MSP40 / MSP50

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: info@m-system.co.jp

EM-4883    P. 8 / 18

9.  COMBINATION WITH VALVE

 

OPERATION DISTANCE WHEN COMBINED WITH VALVE

When setting the upper-stop position and the lower-stop position, it is preferable that the operation distance becomes 80% 
or less with respect to the maximum stroke of the actuator.
That is, when the valve is closed at the lower-end side of the actuator, if the maximum stroke is 20 mm and the lower-stop 
position is set at the 20.0 mm position, there will be no margin for the actuator to further go down to close the valve when 
valve leakage occurs.  In such a case, Auto-setup may not be successfully completed.
In order to avoid such a situation, select an appropriate combination of an actuator and a valve to secure an enough opera-
tion distance.  In the example below, the maximum stroke is 20 mm and thus the preferable operation distance is 16.0 mm. 
Set so that the distance between the upper-stop position and the lower-stop position are within the operation distance of 
16.0 mm.

 

EXAMPLE OF PROPER OPERATION DISTANCE

When connecting the output stem of the actuator with the valve stem, determine their mounting position so that a proper 
operation distance can be secured.

Max. Stroke: 20.0mm

16mm max.  (rough indication)

Upper Stop Position

Lower Stop Position

Valve seat surface (seating position)

Max. Spring contraction

when leakage occurs

Stop

Stop

set by Auto-setup

Spring contraction: approx. 0.1 mm

Upper-End of Max. Stroke

Lower-End of Max. Stroke

• Example of MSP Mounted to Valve

Actuator

Bolts (M5)

Position Indicator

Yoke

Output stem

Lock nut

Valve stem
Valve bonnet

Summary of Contents for MSP40



















Reviews: