background image

R7G-SC-SHL

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: info@m-system.co.jp

EM-7817-A  Rev.2  P. 2 / 7

COMPONENT IDENTIFICATION

X10

X1

STATION  ADD.

PWR

RUN1 RUN2

6M

12M

C1

H1

H

C

C2

H2

HLS

RUN1 ERR1 SD1 RD1

RUN2 ERR2 SD2 RD2

X10

X1

STATION  ADD.

B.RATE

CC-Link

TERM

TERM

ON

OFF

ON

OFF

Operating Mode Setting DIP SW (SW1)

CC-Link Baud Rate Setting Rotary SW

CC-Link Station Address Setting Rotary SW

  CC-Link Terminating 
Resistor SW

CC-Link Status Indicator LED

CC-Link Terminals

Power Supply 
   Terminals

HLS RJ-45 Connectors

HLS Terminating Resistor SW

HLS Station Address Setting Rotay SW

HLS Status Indicator LED

 

STATUS INDICATOR LED

HLS ID

COLOR

FUNCTION

PWR

Green

Turns on when the internal 5V is 
supplied normally.

RUN1/ RUN2

Green

Turns on when the refresh data is 
received normally. 

CC-Link ID

COLOR

FUNCTION

RUN1/ RUN2

Red

Turns on when the refresh data is 
received normally.

ERR1/ ERR2

Red

Turns on when the received data is 
abnormal.

SD1/ SD2

Red

Turns on when the module is trans-
mitting.

RD1/ RD2

Red

Turns on when the module is receiv-
ing.

 

CC-Link STATION ADDRESS 

Station Address is selected between 1 and 63 in decimal.  
The left switch determines the tenth place digit, while the 
right switch does the ones place digit of the address.  Setting 
“n” with the rotary switches, the addresses are assigned to 
n, n+1 for CH1, CH2 respectively.

*  For CC-Link network parameters, the following station infor-

mation for two stations is required.

Station type: Remote I/O, Data allocation: 1

5

4

3

2

1

0

9

8

7

6

5

4

3

2

1

0

9

8

7

6

Station Address Setting (x1)

Station Address Setting (x10)

 

HLS STATION ADDRESS

Station Address is selected between 01H and 3FH in hex-
adecimal.  The left switch determines the sixteenths place 
digit, while the right switch does the ones place digit of the 
address.  
Setting “m” with the rotary switches, the addresses are as-
signed to m, m+1 for CH1, CH2 respectively.

Station Address Setting (x1)

Station  Address Setting (x16)

012

34

56

789AB

C

D

EF

012

34

56

789AB

C

D

EF

Summary of Contents for R7G-SC-SHL








Reviews: