ME401-2
M-Tec ME401-2, Technical Manual v.1.3a, September 2012
Page 4
ENVIRONMENT OR APPLICATION SHALL BE AT
RESELLER’S AND ITS CUSTOMERS’ SOLE RISK, AND M-
TEC SHALL HAVE NO LIABILITY WHATSOEVER IN
CONNECTION THEREWITH. RESELLER SHALL
INDEMNIFY AND HOLD M-TEC AND ITS SUPPLIERS
HARMLESS FROM ANY CLAIM BROUGHT AGAINST M-
TEC WHICH ARISES FROM RESELLER’S USE OR
DISTRIBUTION OF THE PRODUCT IN CONNECTION
WITH SUCH ENVIVRONMENTS OR APPLICATIONS.
SOME STATES AND JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON DURATION OR THE EXCLUSION OF
AN IMPLIED WARRANTY, SO CERTAIN OF THE ABOVE
LIMITATIONS MAY NOT APPLY TO EVERY RESELLER.
Embedded Software/Firmware
The Product and associated tools, if any, may contain
embedded software/firmware, which is licensed, not sold, and
is only for use within the Product as an integral part thereof.
Such embedded software/firmware (which includes all
updates thereto) contains valuable trade secrets and is
proprietary to M-Tec and its suppliers. To the greatest extent
permitted by law, such embedded software/firmware may not
be modified, copied, disassembled, decompiled or reverse
engineered. M-Tec reserves all other rights.
Limitation of Liability
M-TEC’S ENTIRE LIABILITY REGARDING THE PRODUCT
SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID
BY RESELLER FOR THE PRODUCT. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, IN NO
EVENT SHALL M-TEC OR ITS SUPPLIERS BE LIABLE
FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES WHATSOEVER UNDER
ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN
ANY WAY TO THE PRODUCTS, ACCOMPANYING
DOCUMENTATION AND MATERIALS, AND ANY
EMBEDDED SOFTWARE/FIRMWARE AND UPDATES
THERETO (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, LOSS OF DATA OR ANY
OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER
M-TEC HAS BEEN ADVISED OF THE POSSIBILITY OF
ANY SUCH LOSS AND REGARDLESS OF THE COURSE
OF DEALING BETWEEN M-TEC AND RESELLER.
BECAUSE SOME STATES AND JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY
FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE
ABOVE LIMITATION MAY NOT APPLY TO EVERY
RESELLER
.
Notices
Class B Statement – Notice to Users. This equipment has
been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communication. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the
receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician
for help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Regulatory Approvals
CE
The ME401 products comply with the essential requirements
of the R&TTE Directive 1999/5/EC as stated by the EC
Declaration of Conformity (CE0682). The ME401 products
comply with the European Telecommunications Standards
Institute Specifications EN 301 489-1 (EMC for GSM
900MHz and DCS 1800MHZz Radio Equipment and
Systems).
EEC/ International
The ME401 products comply with the essential requirements
of the Automotive directive 2004/104/EC clause 6.5, 6.6, 6.8
and 6.9, UN regulative ECE R10 EMC rev3.
The ME401 products comply with the essential requirements
of the Directive 2003/37/EEC and Directive 2006/42/EEC.
The ME401 products comply with the international standards
ISO-13309, ISO13766 and EN ISO-14982, for tractors, forest
and agricultural machinery, moving machinery and
construction machinery.
The ME401 product comply with the essential and
environmental requirements for use on rolling stock
according to ISO 50121-3-2 and DIN EN 50125-1.
FCC
The ME401 products comply with the FCC Part 15, Part 22
and Part 24, and Industry Canada requirements. The ME401
products comply with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must
accept any interference received, including interference that
may cause undesired operation.
For fixed mounted operations the ME401 must be installed to
provide a separation distance of at least 5 cm from all
persons.
ME401:
FCC ID: ZMF-ME401
IC-ID: 9746A-ME401
