background image

Troubleshooting Guide (Cont.)

Problem

Possible Cause

Solutions

SALL LED’s on flight

controller flash

rapidly and aircraft

will not respond to

transmitter.

Transmitter too near aircraft

during binding process.

Power off the transmitter. Move

the transmitter a larger distance

from the aircraft. Disconnect and

reconnect the flight battery to the

aircraft. Follow the binding

instructions.

Bind switch or button was not held
while transmitter was powered on.

Power off transmitter and repeat

bind process.

Aircraft or transmitter is too close

to large metal object, wireless
source or another transmitter.

Move aircraft and transmitter to

another location and attempt

binding again.

Blue LED on the

receiver flashes

rapidly and the RV

Micro will not respond

to the transmitter

(after binding).

Less than a 5-second wait between

first powering on the transmitter and

connecting the flight battery to the RV

Micro.

Leave the transmitter powered

on. Disconnect and reconnect

the flight battery to the RV

Micro.

The RV Micro is bound to a

different transmitter.

Disconnect and reconnect the

flight battery to the RV Micro.

Power off transmitter and

repeat bind process.

Flight battery or transmitter battery

charge is too low.

Replace or recharge batteries.

Aircraft or transmitter is too close

to large metal object, wireless
source or another transmitter.

Move aircraft and transmitter to

another location and attempt

connecting again.

Crashes immediately

upon lift-off.

Propellers in wrong locations or

incorrect flight mode selected.

Check motor and propeller

orientation and make necessary

flight mode adjustments.

40

Summary of Contents for M1 STEM Drone Series














































Reviews: