background image

12 Month Limited Warranty Information

 

This warranty gives you specific legal rights. You may also have other rights which will vary from state 

to state or province to province.

 

 

M2

 warrants the 

2

-

Axis

 Positioner unit against defects in material and workmanship for a 

period  of  12 

months 

from  date  of  purchase.  During  the  warranty  period, 

M2

  will,  at  its  option,  either  repair  or       

replace products or components which prove to be defective. The warranty shall not apply to defects or 

damage resulting from:

 

 

• 

Improper or inadequate maintenance by user

 

• 

Improperly prepared installation site

 

• 

Unauthorized modifications or misuse

 

• 

Accident, abuse, or misapplication

 

• 

Normal wear

 

 

 

M2

 specifically does not warrant this product for any direct, indirect, consequential, or incidental 

damages arising from the use or inability to use the product. Some states or  provinces do not allow the 

exclusion or limitation of liability for consequential or incidental damages so the above limitation may 

not apply.

 

 

 

In  the  event  repair  or  replacement  are  necessary,  purchaser  shall  contact  M2  for  return         

authorization. In many  cases  this  contact  can  simplify  and  expedite  the repair / replacement  process 

and help reduce costs and downtime.

 

 

 

The purchaser shall be responsible for packing the product properly for return and for charges 

to ship the product to 

M2

. Always include with the shipment, a statement detailing the problem / failure 

and any other pertinent observations. Insuring the product for shipment is  recommended. Use the orig-

inal packing materials whenever possible. 

M2 

is responsible for charges 

(in  the  United  States) 

to re-

turn the repaired / replacement product only where warranty service is involved.

 

 

M2 Antenna Systems, Inc.  4402 N. Selland Ave. Fresno, CA 93722

 

(559) 432

-

8873 Fax (559) 432

-

3059 Web: www.m2inc.com

 

Summary of Contents for FGAE1000-D1-W-COS-A-H



















Reviews: