background image

 

14  

12 MONTH LIMITED WARRANTY 

This warranty gives you specific legal rights. You may also have other rights which will vary from state to state 
or province to province. 
 

M2

 warrants the 

MT-3000AEL

 Positioner unit against defects in material and workmanship for a   

period 

of 12 months 

from date of purchase. During the warranty period, 

M2

 will, at its option, either repair or 

replace products or components which prove to be defective. The warranty shall not apply to defects or dam-
age resulting from: 
 



Improper or inadequate maintenance by user 



Improperly prepared installation site 



Unauthorized modifications or misuse 



Accident, abuse, or misapplication 



Normal wear 

 
 

M2

 specifically does not warrant this product for any direct, indirect, consequential, or inci-

dental damages arising form the use or inability to use the product. Some states or  provinces do not allow the 
exclusion or limitation of liability for consequential or incidental damages so the above limitation may not apply. 
 
 

In the event repair or replacement are necessary, purchaser shall contact M2 for return         authoriza-

tion. In many cases this contact can simplify and expedite the repair / replacement process and help reduce 
costs and downtime. 
 
 

The purchaser shall be responsible for packing the product properly for return and for charges to ship 

the product to 

M2

. Always include with the shipment, a statement detailing the problem / failure and any other 

pertinent observations. Insuring the product for shipment is  recommended. Use the original packing materials 
whenever possible. 

M2 

is responsible for charges 

(in the United States) 

to return the repaired / replacement 

product only where warranty service is involved. 
 
 

M2 Antenna Systems, Inc.  4402 N. Selland Ave. Fresno, CA 93722 

(559) 432-8873 Fax (559) 432-3059 Web: www.m2inc.com 

Summary of Contents for MT-3000A















Reviews: