RTCU LX4 pro Technical Manual V1.00
Advanced Industrial M2M/IoT Gateway
Logic IO ApS.
Ph: (+45) 7625 0210
Holmboes Allé 14
Fax: (+45) 7625 0211
8700 Horsens
Page 38 of 39
Denmark
RTCU LX4 pro
Specifications
Environmental Specification
•
Operating temperature: -30 to 60°C.
•
Battery charge temperature:
-10 to 45 °C
•
Recommended storage temperature:
0 to 45°C.
•
Humidity: 5..90% (non condensing).
•
Ingress Protection: IP20 .
Approvals
•
2014/53/EU Radio Equipment Directive.
•
2014/30/EU EMC Directive
•
2011/65/EU RoHS Directive.
Storage
•
Internal flash drive (Up to 64 MByte).
•
Persistent data flash.
•
Multiple circular dataloggers.
•
SD-card reader.
Cellular Engine
•
LTE Cat.4 Engine (Worldwide).
Max 150 Mbps(DL)/Max 50 Mbps(UL).
LTE FDD: 15 bands.
LTE-TDD: 4 bands.
WCDMA: 7 bands.
GSM: Quad-band.
•
DTMF decoding / transmission.
•
Digitized voice playback / IVR.
•
Internal SIM-card reader.
•
Optional eSIM.
RTCU M2M Platform
•
NX32 for Linux - NX32L.
•
Fully NX32 compatible.
•
Hardened execution environment.
•
Full TLS/SSL support.
Electrical
•
Supply operating range: 8 to 36 VDC.
•
Short and reverse power protected.
LX Hardware Core
•
Powerful 32-bit ARM processor.
•
Hardware floating point and DSP.
•
128 Mbyte RAM.
•
256 Mbyte NAND flash.
•
Real-time clock with battery-backup.
Physical Characteristics
•
Encapsulation:
9 Module M36 DIN-rail.
•
Approx. 430 gram without accessories.
•
W 157 x H 86 x D 58 mm.
(wihout SMA and screw-terminals).
Digital I/O Interface
•
8 x digital solid-state digital output.
Max. 36 volt / 1.5 A per. channel.
Short-circuit, ESD, Inductive kick-back
protected up to 20 mH.
User supplied power source.
•
8 x digital inputs.
Logic high: 8 to 40 VDC.
Logic low: -5 to 3 VDC.
Impedance: 3.3kohm @ 12V.
•
4 x IEC62053-31 Class A input.
Analog I/O Interface
•
4 x analog inputs.
Range is 0..10VDC or 0..20 mA
Resolution: 12 bit
Accuracy: Typ. ±0.5% FSR @ 25°C
Impedance: 40 kohm (V)/504 ohm (C).
•
2 x analog outputs.
Range is 0..10VDC or 0..20 mA
Resolution: 10 bit
Accuracy: Typ. ±0.5% FSR @ 25°C.
•
Protected against transients and low-
pass filtered.
User Interaction
•
144x32 pixels graphical/text display
with black text on green a back-lit
background.
•
Keypad with 8 user defined keys.
•
3 x bi-colour LED / Yellow status LED.
•
DIP-switches.
•
I/O configuration jumpers for digtal
and analog modes.
•
Jumper for RS485 termination
•
Reset / recovery switch.
Battery and Charger
•
On-board 2Ah (nominal) Li-Ion battery.
•
Intelligent charger with temperature
throttle and sub-zero degrees support.
•
On-board temperature sensor.
External Interfaces
•
Two-part pluggable connector for:
Power, I/O, RS232, RS485, Wired M-Bus.
•
RJ45 for LAN with LED status.
•
SD-card slot with presence and write
protect detection.
•
SMA Female connector for cellular.
•
Optional: SMB male for Wireless M-bus.
•
LED indicators and DIP switches.
•
Reset/recovery switch.
•
Mini USB-B as service port.
Communication Interfaces
•
100BASE-T Ethernet interface.
•
1 x RS232 with RTS/CTS.
•
2 x RS485.
•
1-Wire bus with LED support
•
Wired M-Bus with up to 20 slaves.
Compliant with EN13757 2/3.
•
Optional: wM-Bus. Mode S, T, C, R2.
Compliant with EN13757 4/7 OMS.
•
USB service/programming port.
Warranty
•
Two-years return to factory parts and
labor.
•
Optional warranty up to 5 years.
(restrictions apply).
