MAAX 2007 Elite spas, Owner'S Manual

 27 

Temperature

The maximum set temperature is 104°F (40°C) 

and the minimum set temperature is 80°F (27°C). The 
current water temperature or, if the pump has not been 
running, two dashes will show on the display.  If 
dashes are displayed, you must first start the pump by 
pressing the 

JETS 1

 pad.  Wait until the water 

temperature is displayed (approximately 2 minutes). 
 

The set temperature of your spa may easily be 

increased or decreased at any time using the 

SET UP

or 

SET DOWN

 pads. When either of these pads is 

touched, the set temperature will be displayed in the 
LCD window. Each successive touch will change the 
set temperature 1°F in the chosen direction. After 3 
seconds the LCD will automatically display the water 
temperature or dash lines. 
 

If the spa is set in 

Standard

 mode or in a 

filtration cycle, adjusting the set temperature may 
result in activating the heater. When the heater is 
operating, a picture of a thermometer will be displayed 
in the LCD. 
 

Note:

 240-Volt spas that are wired with the 40 Amp 

option will not heat when Pump 1 is on in high speed, 
when Pump 2 is operating or, when pump 3 is 
operating. 
 

JETS 1

 Touch 

the 

JETS 1

 pad to activate the primary 

filtration pump. The sequence of the jet action is: 
 

1 touch = Low whirlpool jets 

2 touches = High whirlpool jets 

3 touches = Off 

JETS 2

 Touch 

the 

JETS 2

 pad to activate the second 

therapy pump. The sequence of jet action is: 
 

1 touch = Low therapy jets 

2 touches = High therapy jets 

3 touches = Off 

JETS 3

 Touch 

the 

JETS 3

 pad to activate the third 

therapy pump. The sequence of jet action is: 

1 touch = Low therapy jets 

2 touches = High therapy jets 

3 touches = Off 

The low speed operation of Pump 1 is timed to 

automatically turn off after two hours of operation. 
The high speed operation of Pump 1, and the low and 
high speed operations of Pump 2 and 3, are timed to 
automatically turn off after 15 minutes of operation. 
 

Note:

 Pump 1 will automatically operate in low speed 

whenever the spa calls for a filtration cycle or heat. 
When this automatic activation occurs, the low speed 
of Pump 1 cannot be turned off; however, all other 
control functions can be activated.

Temperature Lock

Once you have set the desired water temperature, 

you may lock-in the new setting to prevent 
unauthorized temperature adjustments to your spa.  To 
lock the set temperature: 
 Touch 

SET UP

 or 

SET DOWN

, and then touch 

TIME, JETS1,

 and 

SET UP

 within 3 seconds. The 

“TL” indicator will light when the set temperature is 
locked. 

Temperature Unlock

To unlock the temperature, touch either 

SET UP

or 

SET DOWN

, and then touch 

TIME, JETS1,

 and 

SET UP

 within 3 seconds.  The “TL” indicator light 

will go out when the set temperature lock is cleared. 

 
Panel Lock

To help prevent unauthorized use of your spa, the 

control system has a unique panel locking system. 
 

To lock the panel, touch 

TIME, JETS1,

 and then 

SET UP

 within 3 seconds.  When locked, the “PL” 

indicator light will be on.  Except for the time button, 
everything will be frozen. 
 

When the control panel lock is engaged, all 

automatic spa functions will operate normally, but can 
not be altered.