BODYWRAP WHIRLPOOL
SYSTEM ASSEMBLY AND
OPERATION GUIDE
Through routine use, the whirlpool system
can collect residues from soap, bath
additives and natural body oils. Additional
deposits can also collect from minerals or
particles found in the water.
EXTREME CAUTION is urged regarding
the use of any cleaner, acid or solvent on
the whirlpool system trim.
Only use MILD liquid detergent on trim!
Incorrect cleaning materials can
damage finish on trim, drain/overflow
and supply valves.
READ AND FOLLOW ALL PACKAGE
LABELS AND INSTRUCTIONS!
The following procedure is recommended
to remove most deposits and avoid major
accumulations inside the system piping.
The actual schedule for cleaning will
depend on system usage and water
quality, but should not exceed 90 days.
Step 1:
Fill tub to the top of the trim ring on
the highest jet with lukewarm
water. (Figure 4)
Step 2:
Add 1 cup low-sudsing, automatic
dishwasher detergent and run the
whirlpool system for 20 minutes. (
1
complete timer cycle
)
Step 3:
Drain tub, refill with clean water
and operate the system for 20-
minutes (1 complete timer cycle) to
rinse. (
Rinse thoroughly
)
Occasionally sanitize the system by
following the cleaning procedure above,
but substitute 1 cup of household bleach
for the dishwasher detergent. (
Rinse very
thoroughly
)
Refer to the unit installation for guidelines
on unit surface care and cleaning.
WARNING!
NEVER USE ABRASIVE MATERIALS,
NOR ABRASIVE CLEANERS ON THE
WHIRLPOOL TRIM. (JETS, AIR
CONTROLS AND SUCTION COVERS)
Whirlpool System Care and Cleaning
Whirlpool did not start?
"
Check GFCI circuit breaker.
"
Push on/off button to ensure system is
turned "ON".
"
Confirm control box and pump/motor
are plugged in.
"
Confirm wire lead is attached on switch
body and control box.
"
Have wiring connections checked. (
Call
installer or electrician
)
"
Thermal Limiter (in pump) may have
engaged. (
Call installer or supplier
)
Pump "Hums", but no water action?
"
Check air controls, confirm open.
"
Make sure water is to the top of the trim
ring on the highest jet.
"
Check highest side jet for blockage.
(
Rotate internal jet cartridge counter-
clockwise for removal
)
"
Check suction line connection at pump
intake port. (
HAND TIGHTEN UNIONS
ONLY!
)
"
Have pump checked for impeller
obstruction or other malfunction. (
Call
installer or supplier
)
Restricted flow from foot or side jet(s)?
"
Check air controls, confirm open.
"
Confirm side or foot jet is open to full
flow. (Adjust center internal section- see
Figures 8 & 9.)
"
Check side or foot jet for blockage.
(
Rotate internal jet cartridge
counterclockwise for removal
)
"
Have pump-to-jet supply line checked
for blockage. (
Call installer or supplier
)
Water has excessive foaming?
"
Clean and sanitize whirlpool system.
(
See
Whirlpool System Care and
Cleaning
section
)
WARNING!
ANY SERVICING NOT MENTIONED
ABOVE SHOULD BE PERFORMED BY A
QUALIFIED SERVICE
REPRESENTATIVE.
Whirlpool System Trouble Shooting
Before using the whirlpool for the first time,
the system should be cleaned as
described in the
Whirlpool System Care
and Cleaning
section of this guide.
Step 1:
Close the drain and fill tub to
desired water level. Water level
must be at least to the top of trim
ring on highest jet before whirlpool
system is started. (Figure 4)
Step 2:
Check both air controls as shown
in Figure 5. Avoid starting the
whirlpool with the air controls in the
fully closed position.
If the air controls are tightly closed,
rotate the knob counterclockwise
one-half revolution before starting
system.
Step 3:
To start the whirlpool, gently touch
the button as shown in Figure 6.
The built-in 20-minute timer cycle
automatically begins when the
system is started.
To stop the whirlpool during the
timer cycle or to restart the system,
gently touch the switch button.
On systems equipped with an in-line
heater, the heater is automatically
operated through the internal heater
controls.
WARNING!
AVOID OPERATING THE WHIRLPOOL
SYSTEM WITHOUT ADEQUATE WATER
IN THE TUB
Whirlpool System Operation
Page 4
0511
10023064
Figure 4 - Minimum Water Level
Water level must be to top of
trim ring on highest jet
before starting the whirlpool
Jet
Nozzle
Jet Trim
Ring
