46
47
MLMP475iSSP46-M&S-2
MLMP475iSSP46-M&S-2
In
more
detail
. . .
In
more
detail
. . .
Problem
Possible cause
Solution
1. Engine
does not
start
1.1 Not enough fuel in the fuel
tank
1.1 Add fuel
1.2 Spark plug is wet
1.2 Dry spark plug
1.3 Spark plug is damaged
1.3 Replace spark plug
1.4 Spark plug connector is
loose
1.4 Attach properly
1.5 Lever for cutting height
adjustment is not in the
correct position for the
prevailing conditions
1.5 Move the lever to correct
position
1.6
$LU¿OWHULVGLUW\
1.6
&OHDQWKHDLU¿OWHU
1.7 Spark plug is loose
1.7 Tighten the spark plug
(25 to 30 Nm)
1.8 Spark plug gap is incorrect
1.8 Set gap between
electrodes between 0.7-
0.8 mm
1.9 Faulty ignition module
1.9 Contact an authorised
service centre
1.10
Electrical starter battery is
empty
1.10 Charge the electrical
starter battery
1.11
Starter wire disconnected
1.11
Connect the starter wire
to its connector
2. Engine
stops
2.1 Not enough fuel in the fuel
tank
2.1 Fill fuel
2.2 Cutting mean is blocked
2.2 Remove blockage
3. Engine
GLI¿FXOW
to start
or loses
power
3.1 Dirt, water or stale fuel in the
fuel tank
3.1 Drain fuel and clean tank.
Fill the tank with clean,
fresh fuel
3.2 Vent hole in fuel tank cap is
clogged
3.2 Clean or replace the fuel
tank cap
3.3
$LU¿OWHULVGLUW\
3.3
&OHDQDLU¿OWHU
Storage
NOTE:
Good storage conditions are important for keeping your product
trouble-free.
1. Stop the engine and disconnect the spark plug connector (15).
2. Clean the product as described in the “Cleaning” section.
3. Loosen the side levers (8). Unlock the lower handle bar lock (23) and fold the lower
(5) and the upper handle bars (4).
4. Store the product and its accessories in a well-ventilated dry storage area.
5. Always store the product in a place that is inaccessible to children. The ideal
storage temperature is between 10 °C and 30 °C.
6. We recommend using the original package for storage or covering the product
with a suitable cover or enclosure to protect it against dust.
7. For long-term storage (more than 5 days), drain the fuel tank as described in
operator’s manual of the BRIGGS&STRATTON engine (35).
Transportation
1. Stop the engine and disconnect the spark plug connector (15).
2. Adjust the height to the highest position as described in the “Cutting height
adjustment” section.
3. Attach transportation guards, if applicable.
4. Always move the product by the handle (1).
5. If a suitable loading ramp is not available, ask another person for assistance when
loading the product on a vehicle.
6. Protect the product from any heavy impacts or strong vibrations which may occur
during transportation in vehicles.
7. Secure the product with tie-down straps to prevent it from slipping or falling over.
Troubleshooting
6XVSHFWHGPDOIXQFWLRQVDUHRIWHQGXHWRFDXVHVWKDWWKHRSHUDWRUVFDQ¿[WKHPVHOYHV
Therefore, check the product using this section. In most cases, the problem can be
solved quickly.
WARNING!
Only perform the steps described in these instructions! All further
inspection, maintenance and repair work must be performed by an authorised
VHUYLFHFHQWUHRUDVLPLODUO\TXDOL¿HGVSHFLDOLVWLI\RXFDQQRWVROYHWKHSUREOHP
yourself!
Care and maintenance / Troubleshooting
Troubleshooting
