20
GB
MSSP120
Getting
started...
Safety
–
Do not remove any cutting residues or other parts of workpieces from the
cutting zone while the machine is running and the saw unit is not at rest.
–
Support long workpieces (e.g. with a roller table) to prevent them sag
ging at the end of a cut.
–
In an emergency, switch off the machine directly and pull out the pow
er plug.
–
Follow all these instructions before and while you are working with the
saw. Keep these instructions in a safe place.
–
Give these safety regulations to all persons who work on the machine.
–
Do not use this saw to cut fire wood.
–
Never use the saw to cross cut round timber unless it is equipped with
a suitable holding device.
–
The machine is equipped with a safety switch to prevent it being
switched on again accidentally after a power failure.
–
Provide good lighting
–
After you have switched off the motor, never slow down the saw blade
by applying pressure to its side.
–
Faulty saw blades have to be replaced immediately.
–
Never use saw blades which do not comply with the data specified in
this manual.
–
Never dismantle the machines safety devices or put them out of oper
ation.
–
Never cut workpieces which are too small to hold securely in your
hand.
–
Never load the machine so much that it cuts out.
–
It is imperative to observe the manufactureres safety, operating and
maintenance instructions as well as the dimensions quoted in the
technical data.
–
It is imperative to observe the accident prevention regulations in force
in your area as well as all other generally recognized rules of safety.
–
The machine is designed for indoor installation only.
–
Workpieces smaller than the blade guard may lead to injuries to your
hands and fingers. Use suitable aids!
–
Always insert the blade so that the teeth point down toward the table.
–
To avoid broken blades, always set the correct blade tension.
–
Be particularly careful when sawing material with irregular cutting
profiles.
–
Take special care when cutting round workpieces such as rods or
tubes as they may roll away from the blade and cause the teeth to jam.
Secure such workpieces with a wedge.
–
When you withdraw the workpiece the teeth may get caught in the
kerf, particularly if the gap is blocked by sawdust. If this happens you
Summary of Contents for MSSP120
