MAC MAC155L Instruction Manual Download

Page: 28 / 143

MAC155 Rev. 12

Pg 12

WALL MOUNT REMOTE SAMPLING PROBE (OPTION)

If the

Wall Mount Remote Sampling Probe

option is ordered, The Probe will

be mounted on a wall or panel and the sample extracted down a heated line to

the probe. The MAC155 Remote Sampling Probe is equipped with a stainless

steel compression tee tube fitting. The heated sample line is to be connected to

one branch of the tee. The remaining tee branch can either be capped off, or in

the case of long sampling line runs, an external sampling pump can be

connected to insure faster response time. The sample line and tee fitting must

remain above 190 deg F at all times to prevent moisture from condensing out of

the sample. See

page 95

for an outline drawing of the MAC155 Wall Mount

Remote Sampling Probe. See

page 97

for the mounting hole layout for mounting

the probe. The probe should be mounted to the wall or panel using 4) ¼”

fillister

head

screws.

PROBE WIRING

The MAC155 is powered by a nominal 120 VAC, 50/60 HZ @3A max. power

source. The 240V option allows operation from a 240V 50/60Hz @1.5A supply.

Refer to the wiring diagram for probe wiring at the end of this manual for
detailed information

Two connectors are provided on the outside of the MAC155 Probe, refer to

Figure 6. The connector with three (3) pins is the AC power input. The other

connector with 6 pins provides the DC power and RS485 serial communication

lines. Two 6 foot/1.8 meter long cables are shipped with the MAC155 Probe for

termination to these connectors. These cables can be shortened as required for

the installation. Allow enough slack so that the MAC155 Probe can be withdrawn

from the port with the connectors mated. This will make servicing the unit easier.

These cables shall not be extended by splicing or other means. Each cable

should be terminated in a junction box. The AC power and RS485/DC power

Summary of Contents for MAC155L






























































































Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands

MAC MAC155L, Instruction Manual

Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands