MAC MAC155L Instruction Manual Download

Page: 52 / 143

MAC155 Rev. 12

Pg 36

WATER TANK

Before servicing the water tank with the MAC155 Probe in place,
turn off the power and remove the power cable from the unit to
eliminate any possible contact with hazardous voltage.

The MAC155 Probe calibration system uses water that is stored in the water

tank to generate reference gases of a known percent of water vapor by volume.

The water tank holds enough water to last for over a year under normal

operating conditions. Do not wait for the low water level detection circuit to trip.

Instead, a regular maintenance schedule should be set up. The tank should be

drained, flushed, and refilled at least once per year.

Read the “OPERATION” section in this manual for information about filling

the tank.

When it is time to re-fill the water tank, proceed as follows:

1. Remove all electrical power from the instrument, and then open the

cover.

2. Loosen the mounting clamp on the barrel of the MAC155 Probe just

enough to rotate the instrument clockwise approximately 15 degrees.

This will assure that water will not run into the instrument when filling

the tank.

3. Siphon water from the tank as previous described.

4. Flush the tank as previously described.

5. Turn the instrument until it is approximately level and re-fill the tank

with distilled water as previously described. Install the fill plug and

make sure it is tight. Wipe up any water that found its way into the

instrument during this process.

Summary of Contents for MAC155L






























































































Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands

MAC MAC155L, Instruction Manual

Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands