MAC MAC155L Instruction Manual Download

Page: 68 / 143

MAC155 Rev. 12

Pg 52

If the wire has been sized properly, the +/- 15V should measure between

13.5V and 15V.

+5V Digital Power

There is a +5V power supply on the main board for digital devices in the

probe. This supply is powered from the +15V supply. An LED near the center of

the main board, refer to Figure 21 – +5V Power Supply Status Indicator,

indicates the presence of output voltage form this supply. Test points are located

on the left edge of the board slightly above the LED.

+5V Analog Power

There is a pre5V supply on the main board for analog devices. This

supply is powered by the +15V. There is no LED indicator to represent this

supply due to the nature of the low current output available. Test points are

available for the +5V analog supply at the tope edge of the main board, just

below the sensor module.

The +5V analog supply should measure between 4.97V and 5.03V

Status Indicators

A group of (6) six LED’s are located at the bottom of the main board near the center;

Refer to Figure 19 – Main Board Status Indicators

CAL Pump

The “CAL Pump” LED is on when power is applied to the calibration pump. This

LED should be on only during a calibration check cycle or during a calibration.

Case Cool

The “Case Cool” LED is “ON” when the case temperature is above 130°F / 55 °C. If

the probe is equipped with the case cool option, 120V AC is applied to the case cool
solenoid valve and the LED will illuminate to indicate this action. The Case Cool

Summary of Contents for MAC155L






























































































Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands

MAC MAC155L, Instruction Manual

Search results

Summary of Contents for MAC155L

Reviews:

Related manuals for MAC155L

Brands by name

Popular brands