Istruzioni-HCMMMTTT-09022023 (Cod.620100007 Rev.16) EsEng (USA) MAC3.doc
24
ES
Configuración para el interruptor flotante de
funcionamiento en seco (u otro comando externo):
Es posible usar un flotante de minima (u otro comando
externo) para permitir el arranque del variador de frecuencia
dependiendo de la posición del flotante de mínima. El cierre
del contacto permite activar el inversor
Para habilitar la función hay que:
-
Conectar el flotante entre 1 y 2 de J8 (en la tarjeta de
potencia vers.STD)
-
También se puede conectar entre 5 y 6 dei J6 (en la
tarjeta de expansión vers.ADV)
-
Activar la función de “control remoto” en el menú
extendido (par.55)
EN
Configuration for dry running floatswitch (or other
external command):
It’s possible to use a floatswitch (or other external
command) for activation of the inverter. Closing the contact
allows the inverter to be activated.
To use this function:
−
Connect the floatswitch between 1 and 2 on J8 (mother
board for STD version)
−
Or connect the floatswitch between 5 and 6 on J6
(expansion board for ADV version)
−
En
able “remote control” function on extended menu
(par.55)
ES
Configuracion Relè:
Es posible utilizar el relé (R1) en la placa madre como relé
de alarma (para anomalías eléctricas e hidráulicas), haga
funcionar la bomba, o para construir el sistema con una
segunda bomba a una frecuencia fija. Las funciones se
pueden activar a través del menú extendido (par.50).
EN
Relay Configuration:
It’s possible to use the relay (R1) on the mother board as
an alarm relay (for electrical and hydraulic anomalies),
run pump, or to build boosting system with a second
pump at fixed frequency.The functions can be enabled
by the extended menu (par.50).
ES
Configuracion para el modo booster (bomba
ON/OFF):
NB. Es posible utilizar la función Booster sólo
cuando el modo de funcionamiento del inversor
está configurado como AUTOMÁTICO
(par.28).
−
Conecte el control de booster entre C-NO en R1 (tarjeta
madre vers.STD) o entre 24-26 en J8 (tarjeta de
expansión vers.ADV)
−
Ajuste el parámetro 50 "Configur.Relays"
= “R1:Booster” o
“R1:A R2:R R3:B1” para vers.ADV.
−
Ajuste el parámetro 51 "Aument.P.Booster" el valor de
aumento de presión (por estandard = 0,2 bar). Este valor
determina el aumento de la presión del sistema requerida
después de la puesta en marcha de la bomba de ON /
OFF.
Booster Operación:
Cómo arrancar la segunda bomba ON / OFF:
Si la primera bomba no puede alcanzar la presión y la
frecuencia
está
en
el
valor
máximo
de
trabajo
(es.50Hz/60Hz), el inversor pone el comando para iniciar la
segunda bomba ON / OFF.
Tan pronto la segunda bomba se inicia, el inversor
incrementa el valor de la presión del sistema en una
cantidad igual al parámetro 51 "Aument.P.Booster" (por
estandard 0,2 ba r [2.9psi]). Este parámetro determina el
aumento de la presión del sistema para evitar la oscilación.
En caso de necesidad se puede aumentar hasta un máximo
de 1,5 bar [21,75 psi] (de fábrica = 0,2 bar [2.9psi]).
Cómo parar la segunda bomba ON / OFF:
El parámetro que desconecta la segunda bomba es:
parámetro 64 "Umbral Minimo %". (Por estandard = 50%)
Cuando el porcentaje de la potencia es menor que el umbral
y la presión es más alta que la presión del sistema, a
continuación, la unidad desconecta la segunda bomba.
EN
Configuration for Booster mode (ON/OFF pump):
NB. It’s possible to use the Booster function
ONLY when the operating mode of inverter is
configured as AUTOMATIC
(par.28)
.
−
Connect the control of booster between C-NO on R1
(mother board vers.STD) or between 24-26 on J8
(expansion board vers.ADV)
−
Set pa
rameter 50 : ”Relay Configur.” on “R1:Booster” for
STD version or “R1:A R2:R R3:B1” for ADV version.
−
Set the parameter 51 "Inc Pres Booster" the value of
pressure rise (default = 0.2 bar). This value determines
the increase of the system pressure required after the
starting of the pump ON / OFF.
Booster Operation:
How to start second pump ON / OFF:
If the first pump cannot reach pressure system and the
frequency
is
at
the
maximum
working
value
(es.50Hz/60Hz), the drive switch on the command to start
the second pump ON / OFF.
As soon the second pump is started, the drive increase the
system pressure value by an amount equal to the
parameter 51 "Inc Pres Booster" (default 0.2bar [2.9psi]).
This parameter determines the increase of the system
pressure to avoid oscillation. In case of need can be
increased up to a maximum of 1.5 bar [21.75 psi] (default =
0.2 bar [2.9psi]).
How to stop the second pump ON / OFF:
The parameter that switches off the control for the second
pump is:
-parameter 64 "MinTresholdPar". (Default = 50%)
When the percentage of power is lower than the threshold
and the measured pressure is higher than the system
pressure, then the drive switches off the second pump.