Istruzioni-HCMMMTTT-09022023 (Cod.620100007 Rev.16) EsEng (USA) MAC3.doc
41
Falta de Agua
Dry running
Falta de agua
encontrada:
En la versión de HCW,
la válvula de retención
está cerrada mientras
la bomba está
funcionando.
En la versión HCA, la
potencia medida está
por debajo del valor
establecido en el
parámetro ''
Pot.Marcha Seco''.
El inversor intenta
reiniciar 5 veces. Si
fallan, el inversor
queda bloqueado.
La restauración se
intenta de nuevo cada
50 minutos por 24
veces. Entonces el
sistema permanece en
bloque permanente.
Póngase en contacto
con la asistencia
técnica.
-Verifique la presencia
de agua. En la versión.
-HCW verifique que la
válvula de retención
funciona correctamente.
-En la versión HCA
compruebe que el valor
introducido en el
parámetro
“Pot.Marcha
Seco” es correcto.
-Comprobar la correcta
conexión a la bomba y
el cebado de la misma.
-Compruebe que el filtro
no esté obstruido.
-Desconecte la
alimentación. Espere
hasta a que la pantalla
se apague y volver a
restaurar la
alimentación de energía
al sistema.
-Desconecte la fuente
de alimentación.
Espere a que la
pantalla para apagar
Vuelva a conectar la
fuente de alimentación.
Lack of water found:
In the HCW version, the
check valve is closed
while the pump is
running.
In the HCA version the
measured power is
below the value set on
the parameter '' Dry Run
Power ''.
The inverter attempts to
reset 5 times. If they fail,
the inverter remains
blocked.
The restoration is
attempted again every
50 minutes for 24 times.
Then the system
remains in permanent
block.
-Check for water
presence.
-In HCW model verify
check valve.
-In HCA model verify
the value of “Dry Run
Power
”.
-Reset the correct
pump priming
function.
-Check that the filter
is not blocked.
-Disconnect the
power supply and
wait for the display to
switch off.
-Re-connect power
supply.
Fallo de presión
Prs Sensor Fault
Detectado un fallo en
el sensor de presión
-Verifique que el sensor
de presión está
conectado
correctamente.
-Si el problema
persiste, sustituya el
sensor de presión
o contactar con
asistencia técnica
Detected a fault in the
pressure sensor
-Verify that the
pressure sensor is
connected correctly.
-Verify that the value
of the parameter
“PrsSensor Freq" is
greater than 400
value.
-If the problem
persists, replace the
pressure sensor or
contact technical
assistance.
Fallo Max Corr
Overcurrent
Exceso de corriente
en la bomba
-Asegúrese de medir la
corriente de salida con
los parámetros
"corriente de salida" y
establezca el parámetro
correcto "Max Corr.
Motor"
-Asegúrese de que la
bomba se utiliza en las
condiciones prescritas
por el fabricante
Asegúrese de que no
hay condiciones de
fricción o de bloqueo
del rotor
Over current detected in
the pump
-Check current
measurement output
parameter to
"LoadCurrent " and
set the proper
parameter
“Max.MotorCurrent "
-Verify that the pump
is used under the
conditions prescribed
by its manufacturer
and make sure that
there are no
conditions of friction
or locking of the
impeller