background image

Your MACCHIATObin unit should come with a preprogrammed Buildroot file system in its
on-board eMMC storage. If that is not the case or you want to flash a different kernel or file
system to the board, check out BSP HowTo page.

Connecting

Connecting various peripherals to the MACCHIATObin board goes as follows:

1.  Plug your power adapter to the 12V 

DC Jack

.

2.  Connect your PC to your board by plugging the micro USB cable to a USB port on

your laptop/computer and plugging the other end to the 

MicroUSB

 port on your

MACCHIATObin.

3.  Connect one end of an Ethernet cable to the 

RJ45 1GbE

 port on your

MACCHIATObin and the other end to your IP router or IP switch.

4.  (Optional) If you are trying to use the USB storage devices, connect the USB stick to

the 

USB 3.0

 port on the MACCHIATObin.

 

Serial connection

Regarding step 2 from above, we will use serial connection to access the console on
MACCHIATObin. Follow the tutorial for your OS to make sure you have everything needed:

Serial connection - Windows
Serial connection - Linux

 

Start using MACCHIATObin

Booting

When the MACCHIATObin starts to boot, you can check the ATF (ARM Trusted Firmware)
& U-Boot version:

3/7

Summary of Contents for Single Shot








Reviews: