background image

5

STORE THE AIR COMPRESSOR PROPERLY: 

When not in use the air compressor

should be stored in a secure, dry place out of the reach of children. Always lock
up the storage area.

PROTECT YOUR HEARING: 

Ear protection should be worn when operating this

compressor.

MAINTAIN THE AIR COMPRESSOR WITH CARE: 

If the air compressor is damaged in

any way, have it repaired by a qualified service engineer.

EXTENSION LEAD: 

Only use extension leads that are of an appropriate power

rating and suitable for the work environment. Extension leads must have an
earth connection. Inspect the extension lead regularly and replace if
damaged.

ONLY USE PARTS AND ACCESSORIES RECOMMENDED IN THIS MANUAL:

 The use of

unauthorised accessories or attachments is not permitted and may result in
personal injury and damage to the air compressor. Do not attempt to repair or
modify the air compressor.

STAY ALERT: 

Watch what you are doing, use common sense, and do not operate

the air compressor when you are tired. The air compressor should not be used if
you are under the influence of alcohol, drugs or any medication that makes
you drowsy.

BEFORE EACH USE CHECK THE AIR COMPRESSOR AND HOSE FOR DAMAGED
PARTS: 

Never use the air compressor if it has been damaged in any way. Have

the air compressor repaired by a qualified service engineer. Do not use the air
compressor if the On/Off switch does not operate correctly.

HANDLE THE AIR COMPRESSOR CAREFULLY:

 Operate the air compressor

according to the instructions contained within this instruction booklet. This air
compressor should never be operated by children or individuals unfamiliar with
its operation.

KEEP THE MOTOR AIR VENT CLEAR: 

Keep the motor vent clear and free from dust,

wipe regularly to maintain an adequate supply of clean air to the air
compressor.

OPERATE THE AIR COMPRESSOR AT THE CORRECT VOLTAGE:

 Make sure that the

mains supply voltage is the same as the voltage shown on the rating plate.

DO NOT WIPE THE PLASTIC PARTS WITH SOLVENT: 

Do not use solvents or thinners

such as petrol, benzene, carbon tetrachloride or alcohol to clean the air
compressor, as these chemicals will damage the finish. With the air compressor
unplugged from the supply, use a dry cloth to wipe over the plastic casing.

SAFETY PRECAUTIONS

Summary of Contents for airmaster TIGER 9/24

























Reviews: