4 Dismantling/Assembly
4.6 Separator bowl
Fit the hydraulic disc compressing tool. The valve
on the tool should point upwards “Unloaded
position”. Use the handle to tighten the piston rod
in the distributor.
Set the valve on the tool into the left position.
Pump until no resistance can be felt in the handle.
The disc stack has now been compressed by the
hydraulic tool against the bowl hood and the axial
force of the disc stack against the lock ring joint is
thus unloaded.
Tighten the large lock ring by hand, then with a
few blows of a lead hammer until it is tight. Pump
again and tighten the ring finally with blows of the
lead hammer until it is fully tightened.
• If the 0-mark positions are as in ’’Check
points - Threads of large lock ring and bowl
body”, proceed to instructions for “Pressure
checking”.
• If the 0-mark positions are
not
as in “4.6.7
Check point - Limit for thread wear” on page
104, the reason could be an incorrectly
assembled bowl or too many discs in the disc
stack. The bowl hood is not attached to the
bowl body.
Disassemble the bowl and check that it is
correctly assembled. If it is, then remove one or
more discs and repeat the above described
procedure. See also the instructions “ Disc stack”
on page 108.
Pressure checking
The position of the 0-marks are now according to
chapter “Check points - Threads of large lock ring
and bowl body”.
a. The condition that the 0-marks are
exactly aligned with each other has been
fulfilled, or
b. The condition that the 0-mark is exactly
aligned with the felt-pen mark has been
fulfilled.
Pump a few strokes until no resistance is felt in
the handle.
107
Summary of Contents for Tetra Centri A 614HGV-14C
