4.11 Horizontal driving device
10. Mount the bearing. Apply the mounting
washer and hit a few blows on the latter to
ascertain that the bearing is in correct
position. Use a tin hammer.
11. Make certain that the worm gear housing and
the magnet of the cpoling coil have been
properly cleaned. Insert the cooling coil.
12. Clean the bearing seat in the bearing shield
(13). Fit a new corrugated shim (22) and O-
‘ ring (10) into the bearing shield.
The parts are included in the MS-kit.
13. Renew the gasket (11) and fit the bearing
shield. Use the two guide pins in the tool set
to position the shield. Note that the shield can
be fitted in one position only.
If necessary, pull it into position using the
screws or tap its centre with a tin hammer.
14. Press the two tube ends of the cooling coil
(16) into the bearing shield.
15. Fit the washers (17) and nuts (18) and tighten
the coil to the shield.
16. Connect the cooling water to the coil. Supply
the cooling water and check for leakages.
17. Fit the seal strip (13) and the guard (14)
covering the bearing shield (see-previous
illustration).
18. Fill oil before the worm wheel guard is
mounted. Quantity: See “Technical data in
Installation Manual.
Quality: See “5.2
Lubricants” on page 181.
19. Fit the gasket and the worm wheel guard.
20. Fit the motor. Fit the seal strip and the
protection cap of the motor.
21. Fit the gasket and the brake cover.
164
4 Dism antling/Assem bly
10 11 12 13 14
22
'
17 18 19 20 21
Summary of Contents for Tetra Centri A 614HGV-14C
