5.2 Lubricants
5 Lubrication
5.2.4 Lubrication chart, general
Alfa Laval ref. 553216-01, rev. 6
Lubricating points
Type of lubricant
Bowl spindle ball bearings and buffers are
lubricated by oil mist
Lubricating oil as specified in “Recommended
lubricating oils”
Bowl spindle taper
Lube oil, only a few drops for rust protection
Metal buffers of bowl spindle
Lube oil
Bowl:
Sliding contact surfaces and pressure loaded
surfaces such as lock rings, threads of lock
rings, bowl hood and cap nut
Pastes as specified in “Lubricants”
Rubber seal rings
Grease as specified in “Lubricants”
Friction coupling ball bearings
The bearings are packed with grease and sealed
and need no extra lubrication
Electric motor
Follow manufacturer's instructions
NOTE
The Lubrication chart, generai can be complemented with more detailed charts, showing the
lubrication points in detail and what type of lubricant to use.
Instructions related to a specific design of the machine, refer to the general assembly drawings.
Some application processes demand special lubrication.
If not specified otherwise, follow the supplier’s recommendation about method of application.
188
Summary of Contents for Tetra Centri A 614HGV-14C
